Was the entire Lumbar Support System Check performed?

--

Go to Step 2

Go to Lumbar Support System Check

Does the other lumbar support operate properly?

--

Go to Step 6

Go to Step 3

Inspect the rear fuse block PWR SEAT circuit breaker for continuity.

Is PWR SEAT circuit breaker OK?

--

Go to Step 4

Go to Step 5

Replace the rear fuse block.

Is the rear fuse block replacement complete?

--

Go to Lumbar Support System Check

--

Repair the short to ground in CKT 3740 (ORN). Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--

Backprobe the lumbar switch connector with a DMM from cavity G (ORN) to ground.

Is the voltage within the specified range?

10-15 V

Go to Step 7

Go to Step 9

Backprobe the lumbar switch connector with a DMM from cavity G (ORN) to cavity E (BLK).

Is the voltage within the specified range?

10-15 V

Go to Step 8

Go to Step 10

Replace the lumbar switch. Refer to Lumbar Switch Replacement .

Is the lumbar switch replacement complete?

--

Go to Lumbar Support System Check

--

Repair the open in CKT 3740 (ORN) between S312 (LH) or S314 (RH) and the lumbar switch. Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--

Perform the appropriate procedure:

Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--

Was the entire Lumbar Support System Check performed?

--

Go to Step 2

Go to Lumbar Support System Check

Did the other adaptive seat operate properly?

--

Go to Step 10

Go to Step 3

Inspect the rear fuse block MEM T&T Fuse for an open.

Is MEM T&T Fuse OK?

--

Go to Step 4

Go to Step 6

Inspect the rear fuse block IGN 3 RR Fuse for an open.

Is IGN 3 RR Fuse OK?

--

Go to Step 5

Go to Step 8

Replace the rear fuse block.

Is the rear fuse block replacement complete?

--

Go to Lumbar Support System Check

--

Repair the short to ground in CKT 2840 (ORN). Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Step 7

--

Replace MEM T&T Fuse in the rear fuse block.

Is MEM T&T Fuse replacement complete?

--

Go to Lumbar Support System Check

--

Repair the short to ground in CKT 41 (BRN). Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Step 9

--

Replace IGN 3 RR Fuse in the rear fuse block.

Is IGN 3 RR Fuse replacement complete?

--

Go to Lumbar Support System Check

--

Backprobe the adaptive lumbar module connector with a DMM from cavity S (ORN) to ground.

Is the voltage within the specified range?

10-15 V

Go to Step 11

Go to Step 22

Backprobe the adaptive lumbar module connector with a DMM from cavity S (ORN) to cavity A (BLK).

Is the voltage within the specified range?

10-15 V

Go to Step 12

Go to Step 23

1. Turn the ignition switch to the ON position.
2. Backprobe the adaptive lumbar module connector with a DMM from cavity M (BRN) to ground.

Is the voltage within the specified range?

10-15 V

Go to Step 13

Go to Step 24

Backprobe the lumbar switch connector with a DMM from cavity G (ORN) to ground.

Is the voltage within the specified range?

10-15 V

Go to Step 14

Go to Step 25

1. Backprobe the lumbar switch connector with a DMM from cavity F (PNK) (LH) or (LT BLU/WHT) (RH) to ground.
2. Move the lumbar switch in the AUTO/ON position.

Is the voltage within the specified range?

10-15 V

Go to Step 15

Go to Step 29

1. Backprobe the lumbar switch connector with a DMM from cavity E (WHT) (LH) or (PPL) (RH) to ground.
2. Move the lumbar switch in the OFF position.

Is the voltage within the specified range?

10-15 V

Go to Step 16

Go to Step 33

1. Backprobe the lumbar switch connector with a DMM from cavity G (DK BLU) (LH) or (WHT) (RH) to ground.
2. Move the lumbar switch in the IN position.

Is the voltage within the specified range?

10-15 V

Go to Step 17

Go to Step 37

1. Backprobe the lumbar switch connector with a DMM from cavity H (YEL) (LH) or (DK BLU) (RH) to ground.
2. Move the lumbar switch in the OUT position.

Is the voltage within the specified range?

10-15 V

Go to Step 18

Go to Step 41

1. Disconnect the lumbar pump motor.
2. Connect a fused jumper from battery positive voltage (B+) to one lumbar pump motor terminal.
3. Connect a fused jumper from the other lumbar pump motor terminal to ground.

Does the motor run?

--

Go to Step 19

Go to Step 46

1. Turn the ignition switch to the OFF position.
2. Disconnect the adaptive lumbar module connector.
3. Connect a DMM from the lumbar pump motor connector cavity A (BRN) to ground.

Is the resistance less than the specified value?

5 ohms

Go to Step 20

Go to Step 47

Connect a DMM from the lumbar pump motor connector cavity B (GRY) to ground.

Is the resistance less than the specified value?

5 ohms

Go to Step 21

Go to Step 48

Replace the adaptive lumbar module. Refer to Lumbar Component Replacement - Power .

Is the adaptive lumbar module replacement complete?

--

Go to Lumbar Support System Check

--

Repair the open in CKT 2840 (ORN) between S302 and the adaptive lumbar module. Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--

Perform the appropriate procedure:

Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--

Repair the open in CKT 41 (BRN) between the rear fuse block and the adaptive lumbar module. Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--

1. Disconnect the lumbar switch connector.
2. Disconnect the adaptive lumbar module connector.
3. Connect a DMM from the lumbar switch connector cavity G (ORN) to ground.

Is the resistance less than the specified value?

5 ohms

Go to Step 27

Go to Step 26

Connect a DMM from the lumbar switch connector cavity G (ORN) to the adaptive lumbar module connector cavity L (ORN).

Is the resistance less than the specified value?

5 ohms

Go to Step 45

Go to Step 28

Repair the short to ground in CKT 1740 (ORN). Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--

Repair the open in CKT 1740 (ORN) between the adaptive lumbar module and the lumbar switch. Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--

1. Disconnect the lumbar switch connector.
2. Disconnect the adaptive lumbar module connector.
3. Connect a DMM from the lumbar switch connector cavity B (PNK) (LH) or cavity C (LT BLU/WHT) (RH) to ground.

Is the resistance less than the specified value?

5 ohms

Go to Step 31

Go to Step 30

Connect a DMM from the lumbar switch connector cavity B (PNK) (LH) or cavity C (LT  BLU/WHT) (RH) to the adaptive lumbar module connector cavity F.

Is the resistance less than the specified value?

5 ohms

Go to Step 45

Go to Step 32

Repair the short to ground in CKT 2290 (PNK) (LH) or CKT 2292 (LT BLU/WHT) (RH). Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--

Repair the open in CKT 2291 (WHT) (LH) or CKT 2293 (PPL) (RH) between the adaptive lumbar module and the lumbar switch. Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--

1. Disconnect the lumbar switch connector.
2. Disconnect the adaptive lumbar module connector.
3. Connect a DMM from the lumbar switch connector cavity C (WHT) (LH) or cavity B (PPL) (RH) to ground.

Is the resistance less than the specified value?

5 ohms

Go to Step 35

Go to Step 34

Connect a DMM from the lumbar switch connector cavity C (WHT) (LH) or cavity B (PPL) (RH) to the adaptive lumbar module connector cavity E.

Is the resistance less than the specified value?

5 ohms

Go to Step 45

Go to Step 36

Repair the short to ground in CKT 2291 (WHT) (LH) or CKT 2293 (PPL). Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--

Repair the open in CKT 2291 (WHT) (LH) or CKT 2293 (PPL) (RH) between the adaptive lumbar module and the lumbar switch. Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--

1. Disconnect the lumbar switch connector.
2. Disconnect the adaptive lumbar module connector.
3. Connect a DMM from the lumbar switch connector cavity A (DK BLU) (LH) or (WHT) (RH) to ground.

Is the resistance less than the specified value?

5 ohms

Go to Step 39

Go to Step 38

Connect a DMM from the lumbar switch connector cavity A (DK BLU) (LH) or (WHT) (RH) to the adaptive lumbar module connector cavity G.

Is the resistance less than the specified value?

5 ohms

Go to Step 45

Go to Step 40

Repair the short to ground in CKT 1064 (DK BLU) (LH) or CKT 210 (WHT) (RH). Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--

Repair the open in CKT 1064 (DK BLU) (LH) or CKT 210 (WHT) (RH) between the adaptive lumbar module and the lumbar switch. Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--

1. Disconnect the lumbar switch connector.
2. Disconnect the adaptive lumbar module connector.
3. Connect a DMM from the lumbar switch connector cavity F (YEL) (LH) or (DK BLU) (RH) to ground.

Is the resistance less than the specified value?

5 ohms

Go to Step 43

Go to Step 42

Connect a DMM from the lumbar switch connector cavity F (YEL) (LH) or (DK BLU) (RH) to the adaptive lumbar module connector cavity H.

Is the resistance less than the specified value?

5 ohms

Go to Step 45

Go to Step 44

Repair the short to ground in CKT 1065 (YEL) (LH) or CKT 211 (DK BLU). Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--

Repair the open in CKT 1065 (YEL) (LH) or CKT 211 (DK BLU) (RH) between the adaptive lumbar module and the lumbar switch. Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--

1. Reconnect the adaptive lumbar module.
2. Turn the ignition switch to the ON position.
3. Connect a DMM from the lumbar switch connector cavity G (ORN) to ground.

Is the voltage within the specified range?

10-15 V

Go to Step 49

Go to Step 21

Replace the lumbar pump motor. Refer to Lumbar Component Replacement - Power .

Is the motor replacement complete?

--

Go to Lumbar Support System Check

--

Repair the open in CKT 9172 (BRN) between the adaptive lumbar module and the lumbar pump motor. Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--

Repair the open in CKT 9173 (GRY) between the adaptive lumbar module and the lumbar pump motor. Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--

Replace the lumbar switch. Refer to Lumbar Switch Replacement .

Is the lumbar switch replacement complete?

--

Go to Lumbar Support System Check

--

Was the entire Lumbar Support System Check performed?

--

Go to Step 2

Go to Lumbar Support System Check

Inspect the rear fuse block MEM T&T Fuse for an open.

Is MEM T&T Fuse OK?

--

Go to Step 5

Go to Step 3

Repair the short to ground in CKT 2840 (ORN). Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Step 4

--

Replace the MEM T&T Fuse.

Is the fuse replacement complete?

--

Go to Lumbar Support System Check

--

1. Disconnect the lumbar switch connector.
2. Connect a DMM from the lumbar switch cavity G (ORN) to ground.

Is the voltage within the specified range?

10-15 V

Go to Step 6

Go to Step 10

Connect a DMM from the lumbar switch cavity G (ORN) to cavity E (BLK).

Is the voltage within the specified range?

10-15 V

Go to Step 7

Go to Step 11

Does the lumbar move when a memory recall function is performed?

--

Go to Step 8

Go to Step 9

Replace the lumbar switch. Refer to Lumbar Switch Replacement .

Is the LH switch replacement complete?

--

Go to Lumbar Support System Check

--

Replace the memory seat module (MSM). Refer to Memory Seat Control Module Replacement .

Is the MSM replacement complete?

--

Go to Lumbar Support System Check

--

Repair the open in CKT 2840 (ORN) between S326 and the lumbar switch. Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--

Repair the open in CKT 550 (BLK) (RH drive) or CKT 650 (BLK) (LH drive) between S313 and the LH seat switch. Refer to Wiring Repairs in Wiring Systems.

Is the circuit repair complete?

--

Go to Lumbar Support System Check

--