Wipers Delay Mode Inoperative Pulse
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the Wiper/Washer System Check performed? | -- | Go to Step 2 | |
2 |
Does the measurement vary within the specified range? | 39 kohms-680 kohms | Go to Step 4 | Go to Step 3 |
3 | Replace the wiper/washer switch. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle . Is the replacement complete? | -- | -- | |
4 |
Is the measurement within the specified values? | 10.5-15 V | Go to Step 6 | Go to Step 5 |
5 | Repair the open in CKT 477. Is the repair complete? | -- | -- | |
6 | Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement . Is the replacement complete? | -- | -- |
Wipers Delay Mode Inoperative Rainsense
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the Wiper/Washer System Check performed? | -- | Go to Step 2 | |
2 |
Are the wipers operating? | -- | Go to Step 3 | |
3 | Set the wiper switch to the middle AUTO DELAY position. Do the wipers operate in pulse mode (one wipe every 1 to 22 seconds)? | -- | Go to Step 5 | Go to Step 4 |
4 | Rotate the wiper switch to the next highter sensitivity level (towards LO). Does an instant wipe occur when increasing the sensitivity? | -- | Go to Step 6 | |
5 |
Does an instant wipe occur when moving the wiper switch from the maximum sensitivity position (closest to LO) to the 2nd highest sensitivity position? | -- | Go to Step 7 | Go to Step 14 |
6 | Replace the Rainsense module. Refer to Outside Moisture Sensor Replacement . Is the replacement complete? | -- | -- | |
7 |
Is the test light on? | -- | Go to Step 11 | Go to Step 8 |
8 | Connect a test light between Rainsense module connector (harness side) terminal 8 and ground. Is the test light on? | -- | Go to Step 9 | Go to Step 10 |
9 | Repair the open in CKT 651. Is the repair complete? | -- | -- | |
10 | Repair the open in CKT 443. Is the repair complete? | -- | -- | |
11 |
Is there continuity? | -- | Go to Step 12 | Go to Step 13 |
12 | Replace the Rainsense module. Refer to Outside Moisture Sensor Replacement . Is the replacement complete? | -- | -- | |
13 | Repair the open in CKT 482. Is the repair complete? | -- | -- | |
14 | Does an instant wipe occur when moving the wiper switch from the 2nd highest sensitivity position to the 3rd highest sensitivity position? | -- | Go to Step 15 | Go to Step 16 |
15 | Replace the Rainsense module. Refer to Outside Moisture Sensor Replacement . Is the replacement complete? | -- | -- | |
16 | Does an instant wipe occur when moving the wiper switch from the 3rd highest sensitivity position to the 4th highest sensitivity position? | -- | Go to Step 17 | Go to Step 20 |
17 |
| -- | Go to Step 18 | Go to Step 19 |
18 | Remove and reinstall the Rainsense module with new adhesive tape. Refer to Outside Moisture Sensor Replacement . Is the replacement complete? | -- | -- | |
19 | Replace the Rainsense module. Refer to Outside Moisture Sensor Replacement . Is the replacement complete? | -- | -- | |
20 | Does an instant wipe occur when moving the wiper switch from the 4th highest sensitivity position to the 5th highest sensitivity position? | -- | Go to Step 22 | Go to Step 21 |
21 | Replace the Rainsense module. Refer to Outside Moisture Sensor Replacement . Is the replacement complete? | -- | -- | |
22 | Check for an open in CKT 481. Is an open present? | -- | Go to Step 23 | Go to Step 24 |
23 | Repair the open in CKT 481. Is the repair complete? | -- | -- | |
24 | Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement . If the problem persists, replace the rainsense module. Refer to Outside Moisture Sensor Replacement . Is the replacement complete? | -- | -- |
