GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 1999 🢒 Grand Prix 🢒 Body and Accessories 🢒 Body Front End 🢒 Hood Primary Latch Release Cable Replacement

Removal Procedure
  1. Open the hood.
  2. Remove the left front headlamp. Refer to Headlamp Replacement in Lighting Systems.

    3. Important: Block the latch in order to prevent the hood from locking until you have installed the hood release cable.


    Object Number: 363718 Size: SH
  3. Remove the hoor latch release cable from the hood latch.
  4. Remove the front sheet metal diagonal brace. Refer to Front End Sheet Metal Diagonal Brace Replacement .
  5. Remove the air cleaner.
    6. • For the 3.1 engine, refer to Air Cleaner Assembly Replacement in Engine Controls.
    • For the 3.8 engine, refer to Air Cleaner Assembly Replacement in Engine Controls.
  6. Tie a wire or string to the end of the hood release cable, in order to aid in the installation of the new hood release cable. Ensure that the end of the wire or string remains in the engine compartment.

    7. Object Number: 363723 Size: SH
  7. Remove the hood release cable retainers from the engine compartment side rail.
  8. Pull the carpet back in order to access the hood release.

    9. Object Number: 317837 Size: SH
  9. Remove the nut from the parking brake bracket.
  10. Remove the bolts from the bolts from hood release handle.
  11. Remove the hood release cable from the hood release handle.

    12. Object Number: 363889 Size: SH
  12. Using a small flat bladed tool to remove the grommet from the dash panel.
  13. Remove the hood latch release cable from the dash panel.

Installation Procedure
  1. Tie the hood latch release cable to a wire or string. Feed the hood latch release cable grommet through the dash panel.
  2. Apply strip caulk sealer or equivalent around the grommet.

    3. Object Number: 317837 Size: SH
  3. Install the hood latch release cable to the hood release handle.

    4. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  4. Install the bolts to the hood release handle.

    5. Tighten
    Tighten the hood release handle bolts to 5 N·m (44 lb in).

  5. Install the nut to the parking brake bracket.

    6. Tighten
    Tighten the parking brake bracket nut to 5 N·m (44 lb in).

  6. Pull the carpet back.

    7. Object Number: 363723 Size: SH
  7. Install the hood latch release cable retainers to the engine compartment side rail retainers.
  8. Route the hood latch release cable through the radiator support.
  9. Install the air cleaner.
    10. • For the 3.1 engine, refer to Air Cleaner Assembly Replacement in Engine Controls.
    • For the 3.8 engine, refer to Air Cleaner Assembly Replacement in Engine Controls.
  10. Install the front sheet metal diagonal brace. Refer to Front End Sheet Metal Diagonal Brace Replacement .

    11. Object Number: 363718 Size: SH
  11. Install the hood latch release cable to the hood latch.
  12. Install the left front headlamp. Refer to Headlamp Replacement in Lighting Systems.
  13. Remove the block from the latch mechanism.
  14. Close the hood.