Circuit Description
The intake air temperature (IAT) sensor is a thermistor. A thermistor is a resistor whose value varies with temperature. The IAT sensors resistance is high when the air temperature is cold, and the IAT sensors resistance is low when the air temperature is warm. The IAT sensor is wired in series with a fixed resistor in the powertrain control module (PCM). The PCM applies 5 volts to the IAT sensor. The PCM monitors the voltage across the IAT sensor and converts the voltage into a temperature reading. The PCM will receive a high voltage input if the air temperature is cold. The PCM will receive a low voltage input if the air temperature is warm.
Conditions for Running the DTC
The ignition is ON.
Conditions for Setting the DTC
| • | The IAT sensor signal voltage indicates that the intake air temperature is greater than 119°C (246°F). |
| • | The above condition is present for at least 0.5 seconds. |
Action Taken When the DTC Sets
| • | The PCM illuminates the malfunction indicator lamp (MIL). |
| • | The PCM records the operating conditions at the time that the diagnostic fails. The Freeze Frame buffer stores this information. |
| • | The PCM enters the Fail-Safe Function and assumes the intake air temperature is 20°C (68°F), while stopping EGR control. |
Conditions for Clearing the MIL/DTC
| • | The MIL turns OFF after three consecutive passing trips without a fault present. |
| • | A History DTC clears after 40 consecutive warm-up cycles without a fault. |
| • | Use the Clear DTC Information function on the scan tool, or disconnect the PCM battery feed in order to clear the DTC. |
Diagnostic Aids
Check for a faulty electrical connection to the PCM.
Use the Temperature vs Resistance table in order to check the IAT sensor at various temperature levels, and evaluate the possibility of a shifted sensor. A shifted sensor could result in a driveability complaint. Refer to Temperature Versus Resistance .
A fault in the IAT sensor electrical circuit may cause an intermittent malfunction. Inspect the wiring harness and the components for any of the following conditions:
| • | Backed out terminals |
| • | Incorrect mating of terminals |
| • | Broken electrical connector locks |
| • | Incorrectly formed terminals or damaged terminals |
| • | Faulty terminal-to-wiring connections |
| • | Physical damage to the wiring harness |
| • | A broken wire inside the insulation |
| • | Corrosion of electrical connections, of electrical splices, or of terminals |
If a DTC P0112 cannot be duplicated, the Freeze Frame data can be useful in determining vehicle operating conditions when the DTC was set.
Test Description
The numbers below refer to the step numbers in the Diagnostic Table.
-
The Powertrain OBD System Check prompts the technician to complete some basic checks and store the freeze frame data on the scan tool if applicable. This creates an electronic copy of the data taken when the fault occurred. The information is then stored in the scan tool for later reference.
-
This step checks the current IAT sensor reading.
-
This step determines if the fault is present.
-
This step determines if the fault is caused by a shorted signal return circuit or by a malfunctioning IAT sensor.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? | -- | |||
Is the IAT display at or greater than the specified value? | 119°C (246°F) | |||
Is a DTC P0112 set? | -- | Go to Diagnostic Aids | ||
Is the IAT display at or below the specified value? | -40°C (-40°F) | |||
5 |
Is the IAT sensor signal circuit shorted to ground? | -- | ||
6 |
Was a repair necessary? | -- | ||
7 | Replace the IAT sensor. Refer to Intake Air Temperature Sensor Replacement . Is the action complete? | -- | -- | |
8 | Repair the IAT sensor signal (input) circuit. Refer to Wiring Repairs in Wiring Systems. Is the action complete? | -- | -- | |
9 | Replace the PCM. Refer to Powertrain Control Module Replacement . Is the action complete? | -- | -- | |
10 |
Are any DTCs displayed on the scan tool? | -- | Go to the Applicable DTC Table | System OK |
