Step
| Action
| Value(s)
| Yes
| No
|
1
|
- Check the suspected bulbs for damage or an open filament.
- Check the harness connectors to be sure the harness connector
seals are not damaged or missing.
Are the bulbs and harness connectors OK?
| --
|
Go to Step 2
|
Go to Step
17
|
2
| Is the turn lamp that is inoperative a front turn lamp?
| --
|
Go to Step 6
|
Go to Step 3
|
3
|
- Turn the ignition switch to the ON position.
- Turn the turn signal switch to the inoperative side.
- Using a test lamp, backprobe between inoperative tail lamp harness
connector terminal B to ground.
Is the test lamp flashing?
| --
|
Go to Step
5
|
Go to Step 4
|
4
|
| • | LR: Repair poor connection or open in circuit 1414 between S292
and the LR turn signal lamp. |
| • | RR: Repair poor connection or open in circuit 1415 between S291
and the RR turn signal lamp. |
Is the repair complete?
| --
| Go to
Exterior Lights System Check
| --
|
5
|
- Turn the ignition switch to the ON position.
- Turn the turn signal switch to the inoperative side.
- Using a test lamp, backprobe between inoperative tail lamp harness
connector terminal G to ground.
Is the test lamp flashing?
| --
|
Go to Step
18
|
Go to Step 19
|
6
|
- Turn the ignition switch to the ON position.
- Turn the turn signal switch to inoperative side.
| • | LH: Using a test lamp, backprobe between the daytime running lamp
control module harness connector C1 terminal E and ground. |
| • | RH: Using a test lamp, backprobe between the daytime running lamp
control module harness connector C1 terminal G and ground. |
Does the test lamp flash?
| --
|
Go to Step
8
|
Go to Step 7
|
7
|
| • | LH: Repair poor connection or open in circuit 1414 between S292
and the DRL control module harness connector C1 terminal E. |
| • | RH: Repair poor connection or open in circuit 1415 between S291
and the DRL control module harness connector C1 terminal G. |
Is the repair complete?
| --
| Go to
Exterior Lights System Check
| --
|
8
|
| • | LH: Using a test lamp, backprobe between the DRL control module
harness connector C1 terminal B to ground. |
| • | RH: Using a test lamp, backprobe between the DRL control module
harness connector C1 terminal C to ground. |
Is the test lamp flashing?
| --
|
Go to Step
10
|
Go to Step 9
|
9
| Replace the DRL control module. Refer to
Daytime Running Lights (DRL) Control Module Replacement
for service procedure.
Is the repair complete?
| --
| Go to
Exterior Lights System Check
| --
|
10
|
| • | LH: Using a test lamp, backprobe between the underhood accessory
wiring junction block harness connector C2 terminal F11 to ground. |
| • | RH: Using a test lamp, backprobe between the underhood accessory
wiring junction block harness connector C2 terminal F12 to ground. |
Does the test lamp flash?
| --
|
Go to Step
12
|
Go to Step 11
|
11
|
| • | LH: Repair poor connection or open in circuit 14 between the DRL
control module harness connector C1 terminal B and the underhood accessory
wiring junction block harness connector C2 terminal F11. |
| • | RH: Repair poor connection or open in circuit 15 between the DRL
control module harness connector C2 terminal C and the underhood accessory
wiring junction block harness connector terminal F12. |
Is the repair complete?
| --
| Go to
Exterior Lights System Check
| --
|
12
|
| • | LH: Using a test lamp, backprobe between the underhood accessory
wiring junction block harness connector C3 terminal A11 to ground. |
| • | RH: Using a test lamp, backprobe between the underhood accessory
wiring junction block harness connector C3 terminal A12 to ground. |
Does the test lamp flash?
| --
|
Go to Step
14
|
Go to Step 13
|
13
| Replace the underhood accessory wiring junction block. Refer to
Underhood Fuse Block Replacement
in Engine Electrical for service procedure.
Is the repair complete?
| --
| Go to
Exterior Lights System Check
| --
|
14
|
- Using a J 35616-A kit connect jumper wires:
| • | LH: Between connector C141 terminal D female to terminal D male
and terminal A female and termianl A male on circuit 14. |
| • | RH: Between connector C142 terminal D female to terminal D male
and terminal A female and termianl A male on circuit 15. |
- Using a test lamp, backprobe between terminal D of your test leads
and ground.
Does the test lamp flash?
| --
|
Go to Step
15
|
Go to Step 16
|
15
| Replace the headlamp. Refer to
Park/Turn Signal/Side Marker Lamp Replacement
for service procedure.
Is the repair complete?
| --
| Go to
Exterior Lights System Check
| --
|
16
|
| • | LH: Repair poor connection or open in circuit 14 between the underhood
accessory wiring junction block harness connector C3 terminal A11 and C141
terminal D. |
| • | RH: Repair poor connection or open in circuit 15 between the underhood
accessory wiring junction block harness connector C3 terminal A12 and C142
terminal D. |
Is the repair complete?
| --
| Go to
Exterior Lights System Check
| --
|
17
| Replace the damage component.
Is the repair complete?
| --
| Go to
Exterior Lights System Check
| --
|
18
|
| • | LH :Repair an poor connection or an open in circuit 250 between
terminal G and S403. |
| • | RH: Repair an poor connection or an open in circuit 350 between
terminal G and S402. |
Is the repair complete?
| --
| Go to
Exterior Lights System Check
| --
|
19
| Replace the damage bulb or socket.
Is the repair complete?
| --
| Go to
Exterior Lights System Check
| --
|
