Circuit Description
The VCM requires an accurate indication of fuel level for EVAP system diagnosis. The fuel level in the fuel tank changes the rate of vacuum decay for the EVAP system leak DTCs.
The Fuel Level Sensor changes resistance based on fuel level. The Fuel Level Sensor has a signal circuit and a ground circuit. The VCM applies a voltage (about 5 volts) on the signal circuit to the sensor. The VCM monitors changes in this voltage caused by changes in the resistance of the sensor to determine fuel level.
When the fuel tank is full, the sensor resistance is high, and the VCMs signal voltage is only pulled down a small amount through the sensor to ground. Therefore, the VCM will sense a high signal voltage (fuel tank full). When the fuel tank is empty, the sensor resistance is low, and the signal voltage is pulled down a greater amount. This causes the VCM to sense a low signal voltage (fuel tank empty).
The VCM uses the input from the Fuel Level Sensor to calculate the fuel level in the fuel tank. This information is then sent to the IPC through Serial Data.
The diagnostic will not run when the tank is greater than 85% or less than 15% full. (This sensor signal disables the misfire when the fuel levels are less than 15%).
Conditions for Running the DTC
The ignition switch is in the RUN position.
Conditions for Setting the DTC
The fuel level sensor voltage remains above 2.9 volts for more than 20 seconds.
Action Taken When the DTC Sets
The VCM uses a fuel remaining value of 40% for the EVAP system diagnostic tests.
The VCM will not turn ON the MIL.
Conditions for Clearing the MIL/DTC
| • | A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles. |
| • | A warm-up cycle occurs when the coolant temperature has risen 22°C (40°F) from the startup coolant temperature and the engine coolant temperature exceeds 70°C (160°F) during the same ignition cycle. |
| • | Use the scan tool Clear Information function. |
Diagnostic Aids
Important: Fuel level is used to determine EVAP system diagnosis. Always diagnose the fuel level sensor before any other EVAP system components or DTCs.
Do not use the fuel gauge as an indication of a shorted or open circuit as the IPC may always default to EMPTY or FULL depending upon the vehicle model.Check for the following conditions:
| • | A poor connection or damaged harness - Inspect VCM harness connectors for the following: |
| - | Backed out terminals |
| - | Improper mating |
| - | Broken locks |
| - | Poor wire to terminal connections |
| • | Intermittent test - monitor a scan tool or digital voltmeter connected between the related circuits while moving the connectors and harnesses. If the failure is induced, the voltage reading will change. This will help locate a circuit problem. |
Test Description
The numbers below refer to the step numbers in the diagnostic table.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 |
Important: : Before clearing the DTCs, use the scan tool Capture Info to save the Freeze Frame and Failure Records for reference. The control module's data is deleted once the Clear Info function is used. Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? | -- | ||
2 |
Is the voltage greater than the specified value? | 2.9 V | ||
3 | This DTC is intermittent. Are any other DTC stored? | -- | Go to applicable DTC table | Go to Diagnostic Aids |
Is the voltage near the specified value? | 5.0 V | |||
5 | Check for a open in the Fuel Level signal circuit. Was a problem found? | -- | ||
6 | With a test light connected to B+, probe the Fuel Level ground circuit. Is the test light ON? | -- | ||
7 | Check for a short to voltage in the Fuel Level signal circuit. Was a problem found? | -- | ||
8 | Check for an open in the Fuel Level ground circuit. Was a problem found? | -- | ||
9 | Check the electrical connector at the Fuel Level Sender for corrosion and improper mating. Was a problem found? | -- | ||
10 | Repair the circuit as necessary. Refer to Wiring Repairs . Is the action complete? | -- | -- | |
11 | Replace the Fuel Level Sender. Refer to Fuel Sender Assembly Replacement . Is action complete? | -- | ||
12 |
Is the action complete? | -- | -- | |
13 |
Does the scan tool indicate the diagnostic Passed? | -- | ||
14 | Does the scan tool display any additional undiagnosed DTCs? | -- | Go to the Applicable DTC Table | System OK |
