GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The theft deterrent control module sends the fuel continue password to the engine control module (ECM) via the serial data circuit. The ECM verifies the fuel continue password received matches the password stored in memory. If the fuel conitnue password is correct, the ECM enables the starting and fuel delivery systems. When replacing a ECM with a GM SPO replacement part, the new ECM will learn the incoming fuel continue password immediately upon receipt.

Conditions for Running the DTC

The ignition is ON.

Conditions for Setting the DTC

The engine control module (ECM) receives a incorrect password from the theft deterrent deterrent control module.

Action Taken When the DTC Sets

    • The vehicle will not start.
    • The ECM considers this to be a tamper state. The ECM sends a serial data message to the theft deterrent control module to flash the SECURITY indicator.
    • The ECM will not illuminate the malfunction indicator lamp (MIL).

Conditions for Clearing the MIL/DTC

    • A history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
    • The DTC can be cleared by using a scan tool.

Diagnostic Aids

A GM SPO replacement engine control module (ECM) is in a functional state to learn the password from the theft deterrent control module. If the theft deterrent control module is replaced, the ECM must be placed in password learning mode to relearn the new password. Once learned, the password becomes permanent information that remains in the ECM. The loss of ECM battery or ignition voltage does not affect the programmed password information. Refer to Programming Theft Deterrent System Components .

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. Verifies if the condition for setting DTC B3060 is current.

  2. To set this code, the password that the ECM has learned does not agree with the password being received from the theft deterrent control module or the ECM did not received the password from the theft deterrent control module. This condition can occur if the theft deterrent control module has been replaced and the Programming Theft Deterrent System Components procedure has not been performed.

  3. If the ECM resets the DTC after the programming theft deterrent system components procedure has been performed, the theft deterrent control module is malfunctioning.

Step

Action

Yes

No

Schematic Reference: Theft Deterrent System Schematics

Connector End View Reference: Theft Deterrent System Connector End Views

1

Did you perform the Theft Deterrent Diagnostic System Check?

Go to Step 2

Go to Diagnostic System Check - Theft Deterrent

2

Is DTC B3060 set as a current code?

Go to DTC B3060

Go to Step 3

3

Important: If a 10 Minute or 30 Minute Re-Learn Procedure is performed, all keys not learned at that time will be erased and will not be recognized. Perform the Adding Keys procedure on all keys or instruct the customer how to perform the Adding Keys procedure. Refer to Adding Keys .

Perform the Programming Theft Deterrent System Components procedure. Refer to Programming Theft Deterrent System Components .

Is the procedure complete?

Go to Step 4

--

4

  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

Go to Step 5

System OK

5

Important: If a 10 Minute or 30 Minute Re-Learn Procedure is performed, all keys not learned at that time will be erased and will not be recognized. Perform the Adding Keys procedure on all keys or instruct the customer how to perform the Adding Keys procedure. Refer to .

  1. Replace the theft deterrent control module. Refer to Theft Deterrent Module Replacement .
  2. Perform the programming theft deterrent system components procedure. Refer to Programming Theft Deterrent System Components .

Is the replacement complete?

Go to Step 6

--

6

  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

Go to Step 2

System OK