Circuit Description
The controller area network (CAN) is used to receive and transmit data (signal) between engine control module (ECM), the electronic brake/traction control module (EBTCM) and the transmission control module (TCM). The data is constantly being sent back and forth between the modules transferring information from their different inputs, reporting state-of-health, and supplying status messaging. Each module sends signals by toggling the circuit either high or low to produce pulse-width signals which the module decodes. Circuits XR888 and XY888 are the CAN information lines used to transmit the data between the modules.
When the TCM has not received an ECM data signal for a specified amount of time, then DTC U2105 will set. DTC U2105 is a type B DTC.
Condition for Running the DTC
The ignition switch is in the RUN position.
Condition for Setting the DTC
The TCM has not received ECM messaging for 1 second.
Action Taken When the DTC Sets
| • | Early production - The TCM illuminates the service transmission lamp (STL) and sends a MIL request to the ECM on the second consecutive drive trip that the diagnostic runs and fails. The ECM then illuminates the MIL. |
| • | Late production - The TCM flashes the Sport Mode Lamp and sends a MIL request on the second consecutive drive trip that the diagnostic runs and fails. The TCM then illuminates the MIL. |
| • | The ECM records the operating conditions in the Freeze Frame at the time of the MIL request from the TCM. |
| • | The transmission operates in the default mode (maximum line pressure, command 4th gear, inhibit TCC, freeze shift adapts). |
Conditions for Clearing the MIL/DTC
| • | Early production - The TCM turns off the STL as soon as the fault is no longer present. |
| • | Late production - The TCM stops flashing the sport mode lamp as soon as the fault is no longer present. |
| • | The ECM turns off the MIL after three consecutive drive trips during which the TCM sends no MIL request. |
| • | A History DTC clears after forty consecutive warm-up cycles, if no failures are present by this diagnostic or any other emission related diagnostic. |
| • | The scan tool clears the MIL/DTC. |
| • | The TCM cancels the DTC default mode actions when the fault no longer exists and the ignition switch is Off long enough in order to power down the TCM. |
Diagnostic Aids
Vehicles equipped with Fuel Cap Lamps utilize the Sport Mode lamp to indicate a transmission malfunction. In these vehicles, the Sport Mode Lamp flashes at 200 millisecond intervals when the TCM commands the lamp ON.
Vehicles not equipped with Fuel Cap Lamps are equipped with a dedicated Service Transmission Lamp (STL) on the Instrument Panel Cluster (IPC). The STL illuminates steadily when the TCM commands the lamp ON.
Use the J 35616-A connector test adapter kit for any test that requires probing the TCM harness connector or a component harness connector. Using this kit will prevent damage to the harness connector terminals.
Check for the following conditions:
| • | Poor connections at the TCM or at the component. Inspect the harness connectors for any backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wire connection. |
| Refer to General Electrical Diagnosis in Wiring Systems for proper procedure. |
| • | Damaged harness. Inspect the wiring harness for damage. If the harness appears to be OK, observe the scan tool while moving any related connectors and any wiring harnesses. A change in the display may help to locate the fault. |
Test Description
The number below refers to the step number on the diagnostic table.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||
Important: Before clearing the DTC, use the Scan Tool in order to record the Failure Records. Using the Clear Info function erases the Failure Records from the ECM/TCM. Did DTC U2105 reset? | -- | Go to Diagnostic Aids | ||
3 |
Does the Scan Tool transmit live Engine Data values (i.e. TP, ECT Brake Switch)? | -- | Go to Diagnostic Aids | |
4 | Check circuit XR 888 and XY 888 for an short to ground. Refer to General Electrical Diagnosis in Wiring Systems. Was the condition found? | -- | ||
5 | Check circuit XR 888 and XY 888 for an open. Refer to General Electrical Diagnosis in Wiring Systems. Was the condition found? | -- | ||
6 | Repair the wiring as necessary. Refer to Wiring Repairs in Wiring Systems. Is the repair complete? | -- | -- | |
7 | Replace the TCM. Refer to Transmission Control Module Replacement . Is the replacement complete? | -- | -- | |
8 | Perform the following procedure in order to verify the repair:
Does the Scan Tool transmit live engine data values? | -- | System OK |
