Did you perform the Power Mirrors System Check?

--

Go to Step 2

Go to Outside Mirrors System Check

1. Turn the ignition switch to the OFF position.
2. Ground the memory seat diagnostic connector:

•	The connector may be taped into the body harness.

•	The module beeps once in order to acknowledge entrance into the mode 1 diagnostics.

•	If the module does not enter the diagnostic mode, refer to Memory Seats System Check in Seats.

•	Refer to Memory Seat Circuit Description in Seats for a detailed explanation of the memory seat/mirror module diagnostic modes.

3. Operate the DRIVER-1 and the DRIVER-2 recall buttons and the memory set button on the left seat/lock switch. (The module beeps once for each switch input received.)
4. Any time a switch is operated and the module does not beep, the module did not receive the input from that switch.

Are there any switch operations where the memory seat/mirror does not beep?

--

Go to Step 6

Go to Step 3

1. Remove the ground from the memory seat diagnostic connector, then ground the connector again within 5 seconds:

•	The module beeps twice in order to acknowledge entrance into the mode 2 diagnostics.

•	Refer to Memory Seat Circuit Description in Seats for a detailed explanation of the memory seat/mirror module diagnostic modes.

2. Operate the seat switch and the power mirror switch in all directions. (The module beeps once for each open or short circuit to a position sensor or any position sensor discontinuity.)
3. Any time a switch is operated and the module beeps, the module senses a problem with the position sensor.

Are there any switch operations where the memory seat/mirror module beeps?

--

Go to Step 4

Go to Step 11

Test CKT 788 (GRY) for an open or a short.

Is CKT 788 OK?

--

Go to Step 5

Go to Step 9

Test CKT 782 (BLK) for an open or a short.

Is CKT 782 OK?

--

Go to Step 10

Go to Step 9

1. Disconnect the memory seat/mirror module connector C1.
2. Use a J 39200 digital multimeter (DMM) to measure the voltage between the following switches and ground while operating the switches:

•	D8 - Memory set switch

•	D5 - Memory select switch position 1

•	C9 - Memory select switch position 2

Is the voltage within the specified range for each terminal?

10-15 V

Go to Step 10

Go to Step 7

Test the following wiring for an open:

Are all of the circuits OK?

--

Go to Step 8

Go to Step 9

Replace the power mirror switch. Refer to Power Mirror Switch Replacement .

Did you complete the repair?

--

Go to Outside Mirrors System Check

--

Repair the faulty wiring. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

--

Go to Outside Mirrors System Check

--

1. Replace the memory seat/mirror module.
2. Refer to Memory Seat Control Module Replacement in Seats.

Is the repair complete?

--

Go to Outside Mirrors System Check

--

1. The system is functioning properly.
2. If the symptom persists, replace the memory seat/mirror module. Refer to Memory Seat Control Module Replacement in Seats.

Did you complete the repair?

--

Go to Outside Mirrors System Check

--

Did you perform the Power Mirrors System Check?

--

Go to Step 2

Go to Outside Mirrors System Check

1. Disconnect the memory seat/mirror module connector C2.
2. Use a J 39200 digital multimeter (DMM) in order ot measure the voltage to ground from the memory seat/mirror module connector C2 terminal A.

Is the voltage within the specified range?

10-15 V

Go to Step 3

Go to Step 5

Use the DMM in order to measure the voltage between the memory seat/mirror module connector C2 terminal A and terminal B.

Is the voltage within the specified range?

10-15 V

Go to Step 4

Go to Step 6

Replace the memory seat/mirror module. Refer to Memory Seat Control Module Replacement in Seats.

Did you complete the repair?

--

Go to Outside Mirrors System Check

--

Repair the open or the short to ground in the CKT 1340 (ORN) wiring. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

--

Go to Outside Mirrors System Check

--

Repair the open in the CKT 150 (BLK) wiring. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

--

Go to Outside Mirrors System Check

--