Removal Procedure
- Disable the SIR system. Refer to Disabling the SIR System in SIR.
- Remove the right side sound insulator. Refer to Instrument Panel Insulator Panel Replacement .
- Remove the right side IP endcap. Refer to Instrument Panel Outer Trim Cover Replacement .
- Remove the IP cluster. Refer to Instrument Cluster Replacement .
- Remove the retaining screws from the data link.
- Remove the IP lower trim pad. Refer to Instrument Panel Lower Trim Panel Replacement .
- Remove the retaining screws that secure the right side vent duct.
- Remove the retaining screws that secure the left side vent duct.
- Disconnect the electrical connectors from the temperature sensors.
- Remove the right vent duct.
- Remove the left vent duct.
- Remove the radio. Refer to Radio Replacement in Entertainment.
- Remove the AC/heater control. Refer to Control Assembly Replacement in HVAC System - Automatic.
- Remove the right side vent duct fastener.
- Remove the right side vent duct.
- Remove the speaker. Refer to Radio Front Speaker Replacement in Entertainment.
- Remove the right windshield pillar garnish molding. Refer to Windshield Pillar Garnish Molding Replacement in Interior Trim.
- Remove the left windshield pillar garnish molding. Refer to Windshield Pillar Garnish Molding Replacement in Interior Trim.
- Remove the fasteners that secure the IP trim pad.
- Pull the IP trim pad slightly rearward.
- Disconnect the electrical connectors.
- Remove the IP trim pad.
Caution: This vehicle is equipped with a Supplemental Inflatable Restraint (SIR) System. Failure to follow the correct procedure could cause the following conditions:
• Air bag deployment • Personal injury • Unnecessary SIR system repairs • Refer to SIR Component Views in order to determine if you are performing service on or near the SIR components or the SIR wiring. • If you are performing service on or near the SIR components or the SIR wiring, disable the SIR system. Refer to Disabling the SIR System.
Installation Procedure
- Partially install the IP trim pad.
- Connect the electrical connectors.
- Align the IP trim pad with the carrier.
- Install the fasteners in order to secure the IP trim pad.
- Install the left windshield pillar garnish molding. Refer to Windshield Pillar Garnish Molding Replacement in Interior Trim.
- Install the right windshield pillar garnish molding. Refer to Windshield Pillar Garnish Molding Replacement in Interior Trim.
- Install the speaker. Refer to Radio Front Speaker Replacement in Entertainment.
- Install the right side vent duct.
- Install the right side vent duct fastener.
- Install the A/C/heater control. Refer to Control Assembly Replacement in HVAC System - Automatic.
- Install the radio. Refer to Radio Replacement in Entertainment.
- Install the left vent duct.
- Install the right vent duct.
- Install the retainers in order to secure the left vent duct.
- Install the retainers in order to secure the right vent duct
- Install the IP lower trim pad. Refer to Instrument Panel Lower Trim Panel Replacement .
- Install the retainers fastening the data link.
- Install the IP cluster. Refer to Instrument Cluster Replacement .
- Install the right side IP endcap. Refer to Instrument Panel Outer Trim Cover Replacement .
- Install the right sound insulator. Refer to Instrument Panel Insulator Panel Replacement .
- Enable the SIR system. Refer to Enabling the SIR System in SIR.
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
Tighten
Tighten the fasteners to 2 N·m (18 lb in).
