Tools Required

During the course of a vehicle useful life, certain situations may arise which will necessitate the disposal of a live (undeployed) pretensioner. The following information covers the proper procedures for the disposing of a live (undeployed) pretensioner. Deploy the pretensioner before disposal. Do not dispose of a live (undeployed) pretensioner through normal disposal channels until the pretensioner has been deployed. The following information covers the proper procedures for the disposing of a live (undeployed) pretensioner.

The pretensioner can be deployed inside or outside of the vehicle. The method used depends upon the final disposition of the vehicle. Review the following procedures in order to determine which will work best in a given situation.

Refer to Inflator Module Handling and Scrapping for deploying the pretensioner inside vehicle under Vehicle Scrapping Procedure.

Deploy the seat belt pretensioners outside of the vehicle when the vehicle will be returned to service. Situations that require deployment outside of the vehicle include the following:

Deployment and disposal of a malfunctioning seat belt pretensioner is subject to any required retention period.

CAUTION: In order to prevent accidental deployment of the pretensioner which could cause personal injury, do not dispose of an undeployed pretensioner as normal shop waste. The undeployed pretensioner contains substances that could cause severe illness or personal injury if the sealed container is damaged during disposal. Use the following deployment procedures to safely dispose of an undeployed pretensioner. Failure to dispose of a pretensioner as instructed may be a violation of federal, state, or local laws.

CAUTION: When you are deploying a pretensioner for disposal, perform the deployment procedures in the order listed. Failure to follow the procedures in the order listed may result in personal injury.

1. Turn the ignition switch to the OFF position.
2. Remove the ignition key.
3. Put on safety glasses.
4. Remove the seat belt pretensioner from the vehicle. Refer to Seat Belt Retractor Pretensioner Replacement - Left Front or Seat Belt Retractor Pretensioner Replacement - Right Front .
5. When carrying a pretensioner to the deployment area keep the open end of pretensioner pointed away from the body.
6. Clear a space around a bench vice about 1.85 m (6 ft) in diameter for deployment of the seat belt pretensioner. Use a space free of activity. Make sure you have sufficient ventilation.
7. Make sure no loose or flammable objects are in the area.
8. Clamp the pretensioner, near the attachment bolt hole, in the vice.



9. Inspect the J 38826 SIR Deployment Harness and the appropriate pigtail adapter for damage. Replace as needed.
10. Short the 2 SIR deployment harness leads together using one banana plug seated into the other.
11. Connect the appropriate pigtail adapter to the SIR deployment harness.
12. Extend the SIR deployment harness and adapter to full length from the deployment fixture.
13. Connect the pretensioner to the adapter on the deployment harness.

Important: The rapid gas expansion involved with deploying a pretensioner is very loud. Notify all the people in the immediate area that you intend to deploy the seat belt pretensioner.

14. Clear the area of people.




CAUTION: When you are deploying a pretensioner for disposal, perform the deployment procedures in the order listed. Failure to follow the procedures in the order listed may result in personal injury.

15. Separate the 2 banana plugs on the SIR deployment harness.
16. Place a 12-volt minimum/2-amp minimum power source (i.e., vehicle battery) near the shorted end of the harness.
17. Connect the SIR deployment harness wires to the power source. Pretensioner deployment will occur when contact is made.
18. Disconnect the SIR deployment harness from the power source after the pretensioner deploys.



19. Seat one banana plug into the other in order to short the deployment harness leads.
20. If the pretensioner did not deploy, disconnect the adapter and discontinue the procedure. Contact the Technical Assistance Group. Otherwise, proceed to the following steps.
21. Put on a pair of shop gloves.
22. Disconnect the pigtail adapter from the pretensioner as soon as possible.
23. Inspect the pigtail adapter and the SIR deployment harness. Replace as needed.
24. Dispose of the deployed pretensioner through normal refuse channels.
25. Wash hands with a mild soap.