GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 2007 🢒 Vibe - FWD 🢒 Brakes 🢒 Hydraulic Brakes 🢒 Front Disc Brake Pads Replacement

Removal Procedure

    Caution: Refer to Brake Dust Caution in the Preface section.

    Caution: Refer to Brake Fluid Irritant Caution in the Preface section.

    Notice: Refer to Brake Fluid Effects on Paint and Electrical Components Notice in the Preface section.

  1. Use a siphon in order to remove half of the brake fluid from the master cylinder reservoir.
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
  3. Remove the tire and wheel assembly from the vehicle. Refer to Tire and Wheel Removal and Installation .

    4. Object Number: 808146 Size: SH
  4. Install a large C-clamp over the brake caliper. Position the ends of the C-clamp against the rear of the caliper body and against the outer brake pad.
  5. Tighten the C-clamp in order to compress the caliper piston into the caliper bore.
  6. Remove the C-clamp from the caliper.

    7. Object Number: 817035 Size: SH
  7. Remove the 2 caliper bolts.

    8. Object Number: 238894 Size: SH

    Notice: Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its mount and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak.

  8. Remove the caliper housing (2) from the caliper bracket. Support the caliper with a wire (1) in order to prevent damage to the brake hose.

    9. Object Number: 815525 Size: SH
  9. Remove the 2 brake pads (6, 10).
  10. Remove the inner pad wear indicator (3) from the inner pad.
  11. Remove the outer pad wear indicator (5), if equipped, from the outer pad.
  12. Remove the 2 insulators (1, 7).
  13. Remove the 2 pad insulators (2, 8).

    14. Important: Note the location of the upper retainer and the lower retainer. The upper retainer is not interchangeable with the lower retainer.

  14. Remove the 2 brake pad retainers (4, 9).

Inspection Procedure

    Object Number: 238906 Size: SH
  1. Inspect the brake pads for wear. If the pad thickness is less than specification, replace the disc brake pads in axle sets.

    2. Specification
    The minimum brake pad lining thickness is 1 mm (0.039 in).


    Object Number: 815525 Size: SH
  2. Clean the 2 brake pad retainers (4, 9). Inspect the retainers for the following conditions:
    3. • Sufficient rebound
    • No deformation
    • No cracks
    • No wear
    • No rust
    • No dirt
    • If the retainers meet the above conditions, re-use the retainers.
  3. Clean and inspect the disc brake hardware. Replace components if necessary. Refer to Front Disc Brake Mounting and Hardware Inspection .
  4. Clean and inspect the caliper. Repair or replace components as necessary. Refer to Brake Caliper Inspection .

    5. Important: Refinish or replace the rotor ONLY if the condition of the rotor requires service. DO NOT refinish the rotor if the brake pads are the only components requiring service.

  5. Measure the brake rotor thickness. Refinish or replace the rotor as necessary. Refer to Brake Rotor Thickness Measurement .
  6. Measure the brake rotor thickness variation. Refinish or replace the rotor as necessary. Refer to Brake Rotor Thickness Variation Measurement .
  7. Inspect the surface of the brake rotor. Refinish or replace the rotor as necessary. Refer to Brake Rotor Surface and Wear Inspection .
  8. Measure the brake rotor assembled lateral runout. Refinish or replace the rotor as necessary. Refer to Brake Rotor Assembled Lateral Runout Measurement .

Installation Procedure

    Object Number: 728143 Size: SH
  1. If the caliper piston is not compressed into the caliper bore, complete the following steps:
    2. 1.1. Place an old brake pad (2) or a block of wood against the caliper piston.
    1.2. Install a large C-clamp over the body of the brake caliper.
    1.3. Position the ends of the C-clamp against the rear of the caliper body and against the pad or the wood.
    1.4. Tighten the C-clamp in order to compress the caliper piston into the caliper bore.
    1.5. Remove the C-clamp.

    Object Number: 815525 Size: SH
  2. Install the upper brake pad retainer (4) to the caliper bracket.
  3. Install the lower brake pad retainer (9) to the caliper bracket.
  4. Install the inner wear indicator (3) to the inner pad (10).
  5. Install the outer wear indicator (5), if equipped, to the outer pad (6).
  6. Apply disc brake grease to both sides of the inner pad insulator (2).
  7. Install the inner pad insulator to the inner pad.
  8. Install the inner insulator (1) to the inner pad insulator.
  9. Install the inner brake pad to the caliper bracket with the wear indicator facing upward.
  10. Apply disc brake grease to both sides of the outer pad insulator (8).
  11. Install the outer pad insulator to the outer pad (6).
  12. Install the outer insulator (7) to the outer pad insulator.
  13. Install the outer brake pad to the caliper bracket.

    14. Object Number: 817140 Size: SH
  14. Install the caliper housing (10) to the caliper bracket (14).

    15. Notice: Refer to Fastener Notice in the Preface section.

  15. Install the caliper bolts (11, 18).

    16. Tighten
    Tighten the bolts to 34.3 N·m (25.30 lb ft).

  16. Install the tire and wheel assembly to the vehicle. Refer to Tire and Wheel Removal and Installation .
  17. Lower the vehicle.

    18. Caution: Do not move the vehicle until a firm brake pedal is obtained. Failure to obtain a firm pedal before moving vehicle may result in personal injury.

  18. With the engine OFF, gradually apply and release the brake pedal several times in order to position the caliper pistons and the brake pads.
  19. Fill the master cylinder fluid reservoir. Refer to Master Cylinder Reservoir Filling .
  20. Burnish the pads and the rotors. Refer to Brake Pad and Rotor Burnishing .