GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 2007 🢒 Vibe - FWD 🢒 Suspension 🢒 Suspension General Diagnosis 🢒 Steering Gear Replacement

Removal Procedure

    Notice: The steering column must be in the LOCK position before disconnecting the following components:

       • The steering column
       • The steering shaft coupling
       • The intermediate shaft
       • The lower steering shaft
    After disconnecting these components, do not move the front tires and wheels. Failure to follow these procedures may cause improper alignment of some components during installation and result in possible damage to the SIR coil.

  1. LOCK the steering column and verify the front wheels are in the straight ahead position.
  2. Move the silencer pad away from the steering column.

    3. Object Number: 820173 Size: SH
  3. Use paint in order to place match marks on the steering shaft coupling (3) and on the intermediate shaft (4).
  4. Loosen the upper coupling bolt (7).
  5. Remove the lower coupling bolt (6).

    6. Object Number: 820261 Size: SH
  6. Remove the steering column hole cover (4) from the bulkhead.
  7. Install the engine support fixture. Refer to Engine Support Fixture .
  8. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
  9. Remove the front tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation .
  10. Remove the left engine splash shield. Refer to Engine Splash Shield Replacement - Left Side .
  11. Remove the right engine splash shield. Refer to Engine Splash Shield Replacement - Right Side .
  12. Remove the 2 outer tie rod ends (10, 15). Refer to Rack and Pinion Outer Tie Rod End Replacement .
  13. Place a drain pan under the vehicle in order to collect the fluid from the power steering system.

    14. Notice: Refer to Power Steering Hose Disconnected Notice in the Preface section.

  14. Remove the pressure and return pipes (2, 3) from the steering gear.
  15. Remove the bolt and the pipe bracket from the steering gear.
  16. Remove the following components together as a unit. Refer to Front Suspension Crossmember Replacement .
    17. • The steering gear
    • The intermediate steering shaft
    • The front suspension crossmember
    • The trans support
    • The 2  control arms
    • The front stabilizer shaft
  17. Remove the bolt and the rear engine mount insulator from the crossmember.
  18. Remove the 3 bolts and the rear engine mount bracket from the crossmember.

    19. Object Number: 820294 Size: SH
  19. Use paint in order to place match marks on the intermediate shaft (3) and on the steering gear (2).
  20. Remove the bolt (5).
  21. Remove the intermediate shaft (4).
  22. Remove the 4 bolts and the steering gear from the crossmember.

Installation Procedure
  1. Install the rear engine mount bracket to the crossmember.

    2. Notice: Refer to Fastener Notice in the Preface section.

  2. Install the 3 bolts to the rear engine mount bracket.

    3. Tighten
    Tighten the bolts to 64 N·m (47.2 lb ft).

  3. Install the rear engine mount insulator to the crossmember.
  4. Install the bolt to the rear engine mount insulator.

    5. Tighten
    Tighten the bolt to 87 N·m (64.2 lb ft).

  5. If you are replacing the steering gear or the intermediate shaft, copy the match marks from the old parts to the same locations on the new parts.

    6. Object Number: 820261 Size: SH
  6. Install the steering gear (11) and the 4 bolts (7, 12, 13, 14) to the crossmember.

    7. Tighten
    Tighten the bolts to 58 N·m (42.8 lb ft).

  7. Install the intermediate shaft (5) to the steering gear. Align the match marks.
  8. Install the bolt (6) to the intermediate shaft.

    9. Tighten
    Tighten the bolt to 35 N·m (25.8 lb ft).

  9. Install the steering column hole cover (4) to the bulkhead.
  10. Install the following components as a unit. Refer to Front Suspension Crossmember Replacement .
    11. • The steering gear
    • The intermediate steering shaft
    • The front suspension crossmember
    • The trans support
    • The 2  control arms
    • The front stabilizer shaft
  11. Install the 2 outer tie rod ends (10, 15). Refer to Rack and Pinion Outer Tie Rod End Replacement .

    12. Notice: Refer to Installing Hoses without Twists or Bends Notice in the Preface section.

  12. Install the pressure and return pipes (18) to the steering gear.

    13. Tighten
    Tighten the pipe nuts to 23 N·m (17.0 lb ft).

  13. Install the pipe bracket bolt (1).

    14. Tighten
    Tighten the bolt to 7.8 N·m (69.04 lb in).

  14. Install the left engine splash shield. Refer to Engine Splash Shield Replacement - Left Side .
  15. Install the right engine splash shield. Refer to Engine Splash Shield Replacement - Right Side .
  16. Install the front tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation .
  17. Lower the vehicle.
  18. Remove the engine support fixture. Refer to Engine Support Fixture .

    19. Object Number: 820173 Size: SH
  19. Align the match marks on the intermediate shaft (4) and on the steering shaft coupling (3).
  20. Install the lower coupling bolt (6).

    21. Tighten
    Tighten the bolt to 35 N·m (25.8 lb ft).

  21. Tighten the upper coupling bolt (7).

    22. Tighten
    Tighten the bolt to 35 N·m (25.8 lb ft).

  22. Place the silencer pad into the correct position.

    23. Notice: Refer to Using Proper Power Steering Fluid Notice in the Preface section.

  23. Fill the power steering fluid reservoir. Refer to Checking and Adding Power Steering Fluid .

    24. Notice: Refer to Air in the Power Steering System Notice in the Preface section.

  24. Bleed the power steering system. Refer to Power Steering System Bleeding .
  25. Inspect the power steering system for leaks. Repair as necessary.
  26. Measure the wheel alignment. Adjust as necessary. Refer to Wheel Alignment Measurement .