GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 2004 🢒 Vibe - FWD 🢒 DTC 🢒 DTC P0741

Circuit Description

The Powertrain Control Module (PCM) uses signals from the Throttle Position (TP) sensor, Mass Air Flow (MAF) and the Crankshaft Position (CKP) sensor to monitor the engagement of the Torque Converter Clutch (TCC) lock-up status. The PCM then compares the actual data with the TCC lock-up schedule in the PCM memory to detect mechanical trouble of the TCC solenoid, valve body or automatic transaxle.

Conditions for Setting the DTC

DTC P0741 will set when one of the following conditions are met:

    • TCC lock-up does not occur after the PCM commands the TCC to apply.
    • TCC remains locked-up even after the PCM commands the TCC to release.

Action Taken When the DTC Sets

A DTC P0741 is stored and the Malfunction Indicator Lamp (MIL) is turned ON.

Diagnostic Aids

Inspect for the following conditions:

    • Clogged or leaky TCC solenoid
    • Valve body fluid passage clogged
    • Torque converter clutch malfunction
    • Faulty PCM

If this DTC cannot be duplicated, the information included in the freeze frame data can be useful in determining vehicle operating conditions when the DTC was first set.

DTC Confirmation Procedure
  1. Turn the ignition switch to LOCK.
  2. Connect the Scan Tool to Data Link Connector (DLC).
  3. Turn the ignition switch to ON.
  4. Clear the DTC, the pending DTC, and the freeze frame data in PCM memory by using the scan tool.
  5. Start the engine and warm up to normal operating temperature.
  6. Use the scan tool to monitor the operation of the TCC solenoid.
  7. Accelerate vehicle in Drive (D) range and drive at 80 km/h (50 mph) for 10 seconds.
  8. Stop the vehicle.
  9. Test for a pending DTC with the scan tool.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. The Powertrain OBD System Check prompts the technician to complete some basic checks and store the freeze frame data on the scan tool if applicable. This creates an electronic copy of the data taken when the fault occurred. The information is then stored in the scan tool for later reference.

  2. This step checks for proper shift points.

    3.

  3. This step checks for a stuck closed lock-up solenoid.

    4.

  4. This step checks for a leaky lock-up solenoid.

    5.

  5. This step checks the condition of the valve body assembly.

    6.

  6. This step checks for a faulty PCM.

DTC P0741

Step

Action

Yes

No

Schematic Reference: Automatic Transmission Controls Schematics

1

Was the On-Board Diagnostic (OBD) System Check performed?

Go to Step 2

Go to Diagnostic System Check - Engine Controls in Engine Controls - 1.8L (LV6)

2

Does the scan tool display any other DTCs?

Go to applicable DTC table

Go to Step 3

3
  1. Install a scan tool.
  2. Turn the ignition to ON, leaving the engine OFF.
  3. Perform the scan tool Clear DTC Information function.
  4. Operate the vehicle with the scan tool connected.

Did DTC P0741 reset?

Go to Step 4

Go to Diagnostic Aids

4

Perform the Upshifts and Torque Converter Clutch Apply Procedure in Road Test in order to diagnose the mechanical condition of the transaxle.

Was a mechanical failure detected?

Go to Step 11

Go to Step 5

5

  1. Apply 12 volt to the shift lock-up solenoid - positive to wire, negative to case).
  2. Apply 490 kPa (71 psi) of compressed air into shift solenoid inlet.

Did the lock-up solenoid outlet port open and did air escape?

Go to Step 10

Step 6

6

  1. Remove the lock-up solenoid.
  2. Apply 490 kPa (71 psi) of compressed air into the lock-up solenoid inlet port.

Did the lock-up solenoid outlet port stay closed and did no air leak?

Go to Step 10

Go to Step 7

7

Remove valve body and inspect its passages for any obstructions/restrictions. Refer to Solenoids and Wiring Harness Replacement .

Is the valve body in good condition?

Go to Step 8

Go to Step 9

8

  1. Install a known good PCM. Refer to Powertrain Control Module Replacement in Engine Controls - 1.8L (LV6).
  2. Perform the DTC Confirmation Procedure.

Does this DTC reset?

Go to Step 11

Go to Step 12

9

Repair or overhaul valve body assembly.

Is the action complete?

Go to Step 13

--

10

Replace the lock-up solenoid.

Is the action complete?

Go to Step 13

--

11

Refer to Road Test for further diagnosis of the transaxle's performance. Repair as necessary.

Is the action complete?

Go to Step 13

--

12

Replace Powertrain Control Module (PCM). Refer to Powertrain Control Module Replacement in Engine Controls - 1.8L (LV6).

Is the action complete?

Go to Step 13

--

13

Perform the DTC Confirmation Procedure.

Are any DTCs displayed on the Scan Tool?

Go to applicable DTC table

System OK