Circuit Description
The accelerator pedal position (APP) sensor 1 and sensor 2 are located within the accelerator pedal assembly. Each sensor has the following circuits:
| • | A 5-volt reference circuit |
| • | A low reference circuit |
| • | A signal circuit |
This provides the engine control module (ECM) with a signal voltage proportional to accelerator pedal movement. The APP sensor 1 signal voltage at rest position is near the low reference and increases as the pedal is actuated. The APP sensor 2 signal voltage at rest position is near the 5-volt reference and decreases as the pedal is actuated. If the ECM detects that the APP sensor 2 signal voltage is not within the predicted range, DTC P2128 sets.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P2128 Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage
Conditions for Running the DTC
| • | The ignition is ON. |
| • | The ignition voltage is more than 5.23 volts. |
| • | DTC P0641 is not set. |
| • | DTC P2128 runs continuously when the above conditions are met. |
Conditions for Setting the DTC
The ECM detects that the APP sensor 2 voltage is more than 4.87 volts for more than 0.4 second.
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame and/or the Failure Records. |
| • | The control module commands the TAC system to operate in the Reduced Engine Power mode. |
| • | A message center or an indicator displays Reduced Engine Power. |
| • | Under certain conditions the control module commands the engine OFF. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Control Module Connector End Views or Engine Controls Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
2 |
Is the APP sensor 2 voltage parameter more than the specified value? | 4.87 V | Go to Step 4 | Go to Step 3 |
3 |
Did the DTC fail this ignition? | -- | Go to Step 4 | Go to Intermittent Conditions |
4 |
Does the DMM indicate voltage within the specified range? | 4.8-5.2 V | Go to Step 5 | Go to Step 10 |
5 | Probe the APP sensor 2 signal circuit with a test lamp connected to ground. Does the test lamp illuminate? | -- | Go to Step 8 | Go to Step 6 |
6 | Observe the APP Sensor 2 parameter with the test lamp still connected to the APP sensor 2 signal circuit. Does the scan tool indicate voltage at the specified value? | 0 V | Go to Step 9 | Go to Step 7 |
7 | Test the APP sensor 2 signal circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs. Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 13 |
8 | Test the APP sensor 2 signal circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs. Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 11 |
9 | Test the APP sensor 2 low reference circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs. Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 12 |
10 | Test the APP sensor 2 5-volt reference circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs. Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 11 |
11 | Test for shorted terminals and for a poor connection at the engine control module (ECM) harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs. Did you find and correct the condition? | - | Go to Step 16 | Go to Step 15 |
12 | Test for an intermittent and for a poor connection at the accelerator pedal harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs. Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 14 |
13 | Test for an intermittent and for a poor connection at the ECM harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs. Did you find and correct the condition? | Go to Step 16 | Go to Step 15 | |
14 | Replace the accelerator pedal assembly. Refer to Accelerator Pedal Position Sensor Replacement. Did you complete the replacement? | -- | Go to Step 16 | -- |
15 | Replace the ECM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 16 | -- |
16 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 17 |
17 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | System OK | |
