The exterior lighting system includes the following components:

This system also includes all wiring controls and related hardware required for the operation of these lamps.

Low Beam Operation

The headlamp switch operates the low beam headlamps. The headlamp switch is located on the left side of the instrument panel. Turning the knob of the headlamp switch to the furthest position to the right will turn ON the low beam headlamps.

A warning tone will sound as a reminder to turn OFF the headlamp switch, when the ignition switch is in the OFF, LOCK or ACC positions and the driver's door is opened.

High Beam Operation

The turn signal/multifunction switch operates the high beam headlamps. The turn signal/multifunction switch is located on the left side of the steering column. Pulling the lever of the turn signal/multifunction switch toward you until the rear detent position can be felt and then releasing the lever, will cause the headlamp operation to switch between low and high or high and low beam, depending upon the starting point.

High Beam Indicator

During operation of the high beam headlamps, the high beam indicator will be illuminated. The high beam indicator is located on the instrument panel cluster.

Flash-to-Pass Operation

The turn signal/multifunction switch also operates the high beam headlamps in the flash-to-pass mode. Pulling the lever of the turn signal/multifunction switch toward you slightly will activate the high beam headlamps. Holding the lever in this position will maintain high beam headlamp operation for as long as needed. When the lever is released, the previous headlamp operation will resume. Flash-to-pass may be used whether the headlamps are ON or OFF.

The daytime running lamp (DRL) system has the following two primary components:

The DRL system operates either the high beam headlamps at a reduced brightness, or the low beam headlamps at normal intensity along with the park/sidemarker/license lamps and instrument panel lamps, when the following conditions exist:

Perform the following steps in order to temporarily disable the DRL system while idling the vehicle, if necessary:

1. Turn the ignition switch to the OFF or LOCK position.
2. Set the park brake.
3. Start the engine and allow the engine to idle.

The DRL system will remain disabled until the park brake is released.

Day Mode Operation

When the ambient light sensor detects that sufficient lighting conditions exist outside the vehicle, the BCM will operate the high-beam headlamps at a reduced brightness.

Low Light Mode Operation

When the ambient light sensor detects that low lighting conditions exist outside the vehicle, the BCM will operate the low-beam headlamps at normal intensity along with the park, sidemarker, license lamps, and instrument panel lamps.

The front fog lamps are located in the front bumper fascia beneath the headlamp assemblies. The front fog lamp switch is located above the headlamp switch on the left side of the instrument panel. Pressing the right side of the fog lamp switch button will turn the fog lamps ON, as long as the parking lamps are on. When the fog lamps are ON, an indicator on the fog lamp switch will illuminate. Pressing the left side of the switch will turn the fog lamps OFF.

The front turn signal lamps are made up of the front park/turn signal lamps and the front sidemarker lamps, both located on the outboard ends of the headlamp assemblies. The rear turn signal lamps are located in the taillamp assemblies. The front turn signal lamps flash with the rear turn signal lamps when a turn is initiated through using the turn signal/multifunction lever. The front turn signal lamp and the front sidemarker lamp will flash in unison if the park lamps are OFF, but the lamps will flash alternately if the park lamps are ON. The turn signals will operate only with the ignition switch in the RUN position and will not operate during hazard flasher operation.

The front park lamps are made up of the front park/turn signal lamps and the front sidemarker lamps, both located on the outboard ends of the headlamp assemblies. The rear park lamps are made up of the rear park/turn signal lamps and the rear sidemarker lamps located in the taillamp assemblies.

The headlamp switch is used to operate the park lamps. The headlamp switch is located on the left side of the instrument panel. Turning the knob of the headlamp switch to the middle position will turn ON the park lamps.

A warning tone will sound as a reminder to turn OFF the headlamp switch, when the ignition switch is in the OFF, LOCK or ACC positions and the driver's door is opened.

There are stop lamps incorporated into the taillamp assemblies as well as a high-mounted stop lamp, located on the rear shelf, centered along the lower edge of the rear window. The stop lamps operate whenever the brake pedal is depressed.

The backup lamps are located in the taillamp assemblies. The back-up lamps operate when the ignition switch is in the RUN position and the transaxle range selector lever is in REVERSE.

The license lamp is located in the rear bumper fascia just above the license plate opening. The license lamp is in operation whenever the headlamp switch is in either ON position.

The interior lighting system includes the following components:

This system also includes all wiring controls and related hardware that is required for the operation of these lamps.

The instrument panel cluster, the radio, and the interior switches (with illumination provisions), are in operation whenever the headlamp switch is in either ON position. The brightness level or dimming of these lamps is controlled by the instrument panel dimmer switch, which is incorporated into the headlamp switch.

The overhead console reading/courtesy lamps are integrated into the overhead console assembly, mounted to the headliner, above and slightly forward of the front seats. The overhead console (courtesy) lamps are activated whenever a door is opened or whenever the IP dimmer lamp switch (headlamp switch) is rotated past the maximum brightness setting to the next detent position.

The overhead console (reading) lamps may also be activated and individually used by depressing the corresponding reading lamp switch, also located on the overhead console. Depressing the lamp switch again will turn the reading lamps OFF.

The side rail lamps are located above the outboard sides of the back seat, mounted to the headliner. The side rail lamps are activated whenever a door is opened or whenever the IP dimmer lamp switch (headlamp switch) is rotated past the maximum brightness setting to the next detent position. The side rail lamps may be operated individually (sedans only) by depressing the side rail lamp switch located next to the lens.

The vanity mirror lamps are integrated into the mirror housing on the sunshade assembly. The vanity mirror lamps are activated whenever the mirror cover is opened.

The console shift control indicator lamp is integrated into the shift control indicator plate. The indicator lamp is activated whenever the headlamp switch is in either ON position

The instrument panel (IP) compartment lamp is located in the upper right side of the IP compartment. The IP compartment lamp switch is located in the IP compartment support panel, behind the left edge of the IP compartment door. The compartment lamp is activated whenever the IP compartment door is opened.

The ashtray lamp is located on the top of the ashtray bracket, just above the ashtray drawer. The ashtray lamp is activated whenever the headlamp switch is in either ON position.

The front side door courtesy lamps are located on the door trim panels near the rearward edge of the front doors. The side door courtesy lamps are activated whenever a door is opened or whenever the IP dimmer lamp switch (headlamp switch) is rotated past the maximum brightness setting to the next detent position.

The rear compartment lamp is located on the underside of the rear shelf support. The rear compartment lamp operates whenever the rear compartment lid is raised.