Tools Required

J 41820

Notice: Use only the recommended tools for separating the ball joint from the knuckle. Do NOT hammer or pry the ball joint from the knuckle. Failure to use the recommended tools may cause damage to the ball joint and seal.

Important: Use the ignition key in order to unlock the steering column.

1. Turn the steering wheel in order to move the front of the applicable wheel to the outboard most position.

Important: Use ONLY a frame-contact type vehicle lift or a floor jack at the recommended lift points. Do NOT use a suspension-contact type vehicle lift. Do NOT lift the vehicle by the lower control arms.

2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
3. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.



4. Disconnect the ABS wheel speed sensor connector (2).
5. Disconnect the ABS wheel speed sensor jumper harness from the harness retainer clips. Refer to Wheel Speed Sensor Jumper Harness Replacement in Antilock Brake System.
6. Remove the stabilizer shaft link. Refer to Stabilizer Shaft Link Replacement .



7. Remove the cotter pin (1) from the ball stud (3).
8. Loosen the ball stud nut.



9. Install the J 41820 over the ball stud and lower control arm as shown.
10. Rotate the ball stud nut counterclockwise in order to separate the ball stud from the steering knuckle.



11. Remove the lower control arm bolts and nuts.
12. Remove the lower control arm.

1. Install the lower control arm.
2. Install the control arm bolts and nuts.

Important: Align the ball stud cotter pin hole parallel to the knuckle in order to ease the cotter pin installation.

3. Install the ball stud to the knuckle.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install the ball stud castle nut.

Tighten
Tighten the ball stud castle nut to 55 N·m (40 lb ft).





Important: Do NOT loosen the ball stud nut in order to align the ball stud nut slots to the ball stud cotter pin hole.

5. If necessary, tighten the ball stud castle nut in order to align the ball stud castle nut slot (1) to the ball stud cotter pin hole (2) as shown.




Important: Ensure that the cotter pin ends do NOT contact the ABS wheel speed sensor, the ABS sensor connector or the drive axle.

6. Install a NEW cotter pin and bend the ends as shown in either example.
7. Install the stabilizer shaft link. Refer to Stabilizer Shaft Link Replacement .
8. Install the ABS wheel speed sensor jumper harness to the harness retainer clips. Refer to Wheel Speed Sensor Jumper Harness Replacement in Antilock Brake System.



9. Install the ABS wheel speed sensor connector (2).

Important: This is a prevailing torque type fastener. This fastener may be reused ONLY if:

•	The fastener and its counterpart are clean and free from rust

•	The fastener develops 3 N·m (27 lb in) of torque (drag) against its counterpart prior to the fastener seating.

If the fastener does not meet these criteria, REPLACE the fastener.
10. Install the lower control arm nuts.

Tighten
Tighten the lower control arm nuts to 113 N·m (83 lb ft).

11. Install the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
12. Lower the vehicle.