Generator Brace Replacement 3.8L

1. Remove the generator rear brace nut (5).
2. Remove the generator rear brace bolt (3).
3. Remove the generator rear brace (4).

1. Install the generator rear brace (4).
2. Finger start the generator rear brace bolt (3).
3. Finger start the generator rear brace nut (5).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Tighten the generator bolts in the order described. The following is a mandatory torque sequence:

Tighten

1. Tighten the generator rear brace bolt (3) to 50 N·m (37 lb  ft).
2. Tighten the generator rear brace nut (5) to 50 N·m (37 lb  ft).

Generator Brace Replacement 3100

1. Loosen the generator pivot bolt (1).
2. Remove the generator rear brace nut (4).
3. Remove the generator rear brace.

1. Install the generator rear brace.
2. Finger start the generator pivot bolt (1).
3. Finger start the generator rear brace nut (4).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Tighten the generator bolt and nut as described:

Tighten

1. Tighten the generator pivot bolt (1) to 50 N·m (37 lb  ft).
2. Tighten the generator rear brace nut (4) to 25 N·m (18 lb  ft).

Generator Brace Replacement 3800 L67 (VIN 1) Rear

1. Remove the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement in Engine Mechanical - 3.8L.
2. Remove the EVAP canister purge solenoid valve. Refer to Engine Controls - 3.8L.



3. Remove the generator rear brace nut (2).
4. Remove the generator rear brace bolt (1).
5. Remove the generator rear brace.

1. Install the generator rear brace.
2. Finger start the generator rear brace bolt (1).
3. Finger start the generator rear brace nut (2).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Tighten the generator bolts in the order described. The following is a mandatory torque sequence:

Tighten
Tighten the generator rear brace bolt (1) to 50 N·m (37 lb  ft).

Tighten
Tighten the generator rear brace nut (2) to 50 N·m (37 lb  ft).

5. Install the EVAP canister purge solenoid valve. Refer to Engine Controls - 3.8L.
6. Install the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement in Engine Mechanical - 3.8L.