Rear Compartment Lid Emblem/Nameplate Replacement Center

Tools Required

J 25070 Heat Gun

1. When replacing or repairing an emblem/nameplate do the following:

1.1.	Use tape to protect the mounting surface during removal.

1.2.	Use tape for alignment marks for installation of the emblem/nameplate.




2. To remove an emblem/nameplate, heat the emblem/nameplate using J 25070 .
3. Apply heat using a circular motion for about 30 seconds.




Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.

4. Use a plastic, flat-bladed tool to lift or remove the emblem/nameplate from the panel surface.

Important: If tape is still intact on the molding or panel, do not remove the tape. Clean the tape and the mating surface with adhesive cleaner. Wipe the tape and the mating surface with a clean, lint free cloth. If the tape is damaged, continue with the replacement procedure.

5. Apply the adhesive foam tape to the back of the emblem/nameplate and press the emblem/nameplate in place.
6. When replacing, remove all adhesive as follows:

•	For body panels, use a 3M™ Scotch Brite molding adhesive remover disk 3M™ P/N 07502 or equivalent.

•	For plastic panels, use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol and water to remove the adhesive.

Important: Apply the emblem/nameplate in an environment that is free from dust or other dirt that could come into contact with the sticky backing. Foreign material may cause improper adhesion.

1. Clean the area where the emblem/nameplate will be installed.

Use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol and water to clean the area.

2. Dry the area thoroughly.



3. Apply tape and mark the location as shown.
4. Heat the mounting surface to approximately 27-41°C (80-105°F) using the J 25070 , if necessary.
5. Ensure that the temperature of the emblem/name plate is approximately 29-32°C (85-90°F).
6. Remove the protective liner from the back of the emblem/name plate.
7. Position the emblem/name plate to the location marks and press the emblem/name plate to the mounting surface.
8. Apply equal pressure along the emblem/name plate to uniformly bond the item to the mounting surface.
9. Remove the protective tape from the mounting surface.

Rear Compartment Lid Emblem/Nameplate Replacement Left

Tools Required

J 25070 Heat Gun

1. When replacing or repairing an emblem/nameplate do the following:

1.1.	Use tape to protect the mounting surface during removal.

1.2.	Use tape for alignment marks for installation of the emblem/nameplate.




2. To remove an emblem/nameplate, heat the emblem/nameplate using J 25070 .
3. Apply heat using a circular motion for about 30 seconds.




Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.

4. Use a plastic, flat-bladed tool to lift or remove the emblem/nameplate from the panel surface.

Important: If tape is still intact on the molding or panel, do not remove the tape. Clean the tape and the mating surface with adhesive cleaner. Wipe the tape and the mating surface with a clean, lint free cloth. If the tape is damaged, continue with the replacement procedure.

5. Apply the adhesive foam tape to the back of the emblem/nameplate and press the emblem/nameplate in place.
6. When replacing, remove all adhesive as follows:

•	For body panels, use a 3M™ Scotch Brite molding adhesive remover disk 3M™ P/N 07502 or equivalent.

•	For plastic panels, use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol and water to remove the adhesive.

Important: Apply the emblem/nameplate in an environment that is free from dust or other dirt that could come into contact with the sticky backing. Foreign material may cause improper adhesion.

1. Clean the area where the emblem/nameplate will be installed.

Use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol and water to clean the area.

2. Dry the area thoroughly.



3. Apply tape and mark the location as shown:

•	Location a--36.7 mm (1.44 in)

•	Location b--63.5 mm (2.5 in)

4. Heat the mounting surface to approximately 27-41°C (80-105°F) using the J 25070 , if necessary.
5. Ensure that the temperature of the emblem/name plate is approximately 29-32°C (85-90°F).
6. Remove the protective liner from the back of the emblem/name plate.
7. Position the emblem/name plate to the location marks and press the emblem/name plate to the mounting surface.
8. Apply equal pressure along the emblem/name plate to uniformly bond the item to the mounting surface.
9. Remove the protective tape from the mounting surface.

Rear Compartment Lid Emblem/Nameplate Replacement Right

Tools Required

J 25070 Heat Gun

1. When replacing or repairing an emblem/nameplate do the following:

•	Use tape to protect the mounting surface during removal.

•	Use tape for alignment marks for installation of the emblem/nameplate.




2. To remove an emblem/nameplate, heat the emblem/nameplate using J 25070 .
3. Apply heat using a circular motion for about 30 seconds.




Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.

4. Use a plastic, flat-bladed tool to lift or remove the emblem/nameplate from the panel surface.

Important: If tape is still intact on the molding or panel, do not remove the tape. Clean the tape and the mating surface with adhesive cleaner. Wipe the tape and the mating surface with a clean, lint free cloth. If the tape is damaged, continue with the replacement procedure.

5. Apply the adhesive foam tape to the back of the emblem/nameplate and press the emblem/nameplate in place.
6. When replacing, remove all adhesive as follows:

•	For body panels, use a 3M™ Scotch Brite molding adhesive remover disk 3M™ P/N 07502 or equivalent.

•	For plastic panels, use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a 50/50 mixture by volume of isopropyl alcohol and water to remove the adhesive.

Important: Apply the emblem/nameplate in an environment that is free from dust or other dirt that could come into contact with the sticky backing. Foreign material may cause improper adhesion.

1. Clean the area where the emblem/nameplate will be installed.

Use a lint free cloth and VMP naphtha or a 50/50 mixture by volume of isopropyl alcohol and water to clean the area.

2. Dry the area thoroughly.



3. Apply tape and mark the location as shown:

•	Location a--56 mm (2.20 in)

•	Location b--63 mm (2.48 in)

4. Heat the mounting surface to approximately 27-41°C (80-105°F) using the J 25070 , if necessary.
5. Ensure that the temperature of the emblem/name plate is approximately 29-32°C (85-90°F).
6. Remove the protective liner from the back of the emblem/name plate.
7. Position the emblem/name plate to the location marks and press the emblem/name plate to the mounting surface.
8. Apply equal pressure along the emblem/name plate to uniformly bond the item to the mounting surface.
9. Remove the protective tape from the mounting surface.