The brake systems use conventional braking under normal operating conditions. The following components are necessary for operation of conventional braking:
Each front channel consists of the following components:
The following conditions exist under normal operating conditions (base brakes):
The following actions permit the above conditions to exist:
The ABS VI improves the controllability and the steerability of a vehicle during braking. The ABS VI improves the controllability and steerability by controlling the hydraulic pressure that applies to each wheel brake.
Antilock braking occurs when the following conditions exist:
When the above conditions exist, the EBCM allows the ABS brake modulator to change the brake pressure several times per second.
The above action causes the following conditions:
The ABS VI cannot perform the following actions:
The ABS VI provides the following conditions:
If any wheel(s) begin to approach lock-up, the EBCM will control the following components in order to control the brake pressure to the affected wheel(s):
During front wheel ABS operation, the solenoids turn on in order to isolate the brake pressure to the affected wheel(s).
The EBCM then provides controlled current to the motors in order to regulate the following items:
The following actions occur when the EBCM provides controlled current:
If ABS was entered during low brake pressure (such as on ice) and a dry surface is encountered during the reapply action, the piston drives all of the way to the top. Driving the piston to the top position causes the following conditions:
The total brake pressure during ABS must not exceed the brake pressure that was present when ABS was entered.
Reduced pressure on the brake pedal may cause the wheel brake pressure to exceed the brake pressure at the master cylinder. The following actions result when the above condition occurs:
The ABS VI cannot increase the brake pressure above the master cylinder pressure that the driver applies.
The ABS VI cannot apply the brakes by itself.
The following actions occur when the ABS is no longer required:
The operation of the rear channel is similar to operation of the front channels except for the following actions that exist in the rear channel:
No rear solenoid exists. The front brakes perform most of the braking.
If an ABS failure that affects the operation of the rear base brake occurs, the following actions will occur:
The Expansion Spring Brake (ESB) holds the piston in the upmost (home) position of the piston.
An ESB is a spring that is retained in a housing at a close tolerance. One end of the spring touches the motor drive dog. The other end of the spring touches the pinion drive dog.
During normal braking, brake pressure exists at the top of the piston. The pressure applies a downward force. The downward force applies a counterclockwise torque to the motor pinion. The motor pinion tries to rotate the spring counterclockwise. The counterclockwise torque expands the spring outward within the housing. Outward expansion of the spring within the housing prevents gear rotation.
The following actions occur when the motor is on and tries to drive the ball screw nut:
The most common application of this principle is in window crank mechanisms. A small amount of force on the crank handle will cause the window to move upward or downward, but the weight of the window (or any pressure on the window) does not cause the window to move downward. In the ESB, the brake pressure at the top of the pistons corresponds to the weight of the window. The motor corresponds to the window crank handle.
The EBCM performs self-diagnostics during initialization.
The EBCM also verifies correct operation of the following components during initialization:
The EBCM inspects the wheel speed sensor circuitry for the following conditions during initialization:
If the EBCM detects a malfunction in itself or in other ABS VI components, the EBCM will perform the following actions:
The following indicators will remain on for approximately three seconds with the key in the ON position:
The initialization performs during engine cranking and engine starting. A slight mechanical noise may be heard during the system initialization. This noise is normal.
If the brake pedal depresses when the engine starts, the system will not initialize. The system will initialize when one of the following actions occurs:
If brake pedal pressure interrupts the system initialization, a slight movement in the brake pedal may exist.
The standard brake system uses a single red BRAKE warning indicator, which is located in the instrument panel cluster.
The antilock brake system uses the following indicators:
The following indicators will turn ON for approximately three seconds and then turn OFF when the ignition is turned to the ON position:
As the engine is cranked, the red BRAKE warning indicator and the amber ABS indicator should illuminate steady.
Three seconds after the engine is started, ABS and ABS ACTIVE indicators should be OFF. The red BRAKE warning indicator will go OFF immediately.
Whenever the vehicle is involved in an ABS stop, the ABS ACTIVE indicator will illuminate, notifying the driver that ABS is in operation.
Using the compact spare supplied with the vehicle will not affect the operation of ABS. The EBCM software can compensate for this smaller tire. However, increased stopping distances may occur due to reduced tire tread depth on compact spare tires.
Tire size is important for proper performance of the ABS. Replacement tires should be the same size, load range, and construction as the original tires. Replace tires in axle sets and only with tires of the same Tire Performance Criteria (TPC) specification number. Use of any other tire size or type may seriously affect the ABS operation.
Refer to Tires and Wheels in Suspension for more information.
