SMU - Revised DTC P0462 Fuel Level Sensor Circuit Low Voltage Diagnostic Procedure
| Subject: | Revised DTC P0462 Fuel Level Sensor Circuit Low Voltage Diagnostic Procedure |
| Models: | 2000 Chevrolet Camaro |
| 2000 Pontiac Firebird |
| With 3.8L Engine |
This bulletin is being issued to revise the DTC P0462 Fuel Level Sensor Circuit Low Voltage diagnostic procedure in the Engine Controls - 3.8L sub-section of the Service Manual. Please replace the current information in the Service Manual with the following information.
The following information has been updated within SI2000. If you are using a paper version of this Service Manual, please make a reference to this bulletin on the affected page.
Circuit Description
The fuel level sensor changes resistance based on fuel level. The fuel level sensor has a signal circuit and a ground circuit. The PCM applies a voltage (about 5.0 volts) on the signal circuit to the sensor. The PCM monitors changes in this voltage caused by changes in the resistance of the sensor to determine fuel level.
When the fuel tank is full, the sensor resistance is high, and the PCMs signal voltage is only pulled down a small amount through the sensor to ground. Therefore, the PCM will sense a high signal voltage (fuel tank full). When the fuel tank is empty, the sensor resistance is low, and the signal voltage is pulled down a greater amount. This causes the PCM to sense a low signal voltage (fuel tank empty).
The PCM uses inputs from the fuel level sensor to calculate the total fuel remaining in the fuel tank. This information is then sent to the fuel gauge.
This DTC sets when the PCM senses a signal voltage lower than the normal operating range of the sensor.
Conditions for Running the DTC
The ignition switch is in the RUN position.
Conditions for Setting the DTC
| • | The fuel level sensor voltage is below 0.39 volts. |
| • | All conditions present for 6.0 minutes. |
Diagnostic Aids
The vehicle fuel gauge displays empty with this DTC set:
Using Freeze Frame and/or Failure Records data may aid in locating an intermittent condition. If you cannot duplicate the DTC, the information included in the Freeze Frame and/or Failure Records data can aid in determining how many miles since the DTC set. The Fail Counter and Pass Counter can also aid determining how many ignition cycles the diagnostic reported a pass and/or a fail. Operate the vehicle within the same freeze frame conditions (RPM, load, vehicle speed, temperature etc.) that you observed. This will isolate when the DTC failed.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? | -- | Go to Powertrain On Board Diagnostic (OBD) System Check | |
Does the scan tool indicate fuel level above the specified value? | 0% | |||
3 |
Does the scan tool indicate that this diagnostic failed this ignition? | -- | Go to Diagnostic Aids | |
4 |
Does the scan tool indicate fuel level above the specified value? | 0% | ||
5 | Test the signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||
6 | Test the fuel sender pigtail circuits for a short together or a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||
7 | Replace the fuel level sensor. Refer to Fuel Level Sensor Replacement. Did you complete the replacement? | -- | -- | |
8 | Inspect for poor connections at the PCM. Refer to Testing for Intermittent and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||
9 |
Important: The replacement PCM must be programmed. Replace the PCM. Refer to PCM Replacement/Programming. Did you complete the replacement? | -- | -- | |
10 |
Does the DTC reset? | -- | ||
11 | Does the scan tool display any DTCs that you have not diagnosed? | -- | Go to applicable DTC | System OK |
