Air Conditioning Condenser Replacement L36

Tools Required

J 39400-A Halogen Leak Detector

1. Recover the refrigerant. Refer to Refrigerant Recovery and Recharging .
2. Remove the upper tie bar support brace bolts at the upper tie bar.
3. Loosen the upper tie bar support brace bolts at the headlamp and bumper fascia mounting panel and position the braces out of the way.



4. Remove the upper radiator seal.



5. Remove the upper radiator mounting brackets.



6. Remove the compressor hose nut from the condenser.
7. Remove the compressor hose from the condenser.
8. Remove the headlamps. Refer to Headlamp Replacement in Lighting Systems.
9. Remove the evaporator hose nut from the condenser.



10. Remove the evaporator hose from the condenser.
11. Remove and discard the sealing washers from the compressor hose and the evaporator hose.



12. Remove the lower hood latch support bolts (1).



13. Remove the fasteners (1) from the left and right sides of the front fascia support.
14. Lift and pull forward on the headlamp and bumper fascia support to obtain access to the condenser mounting bolts.

Important: The bolt retaining the condenser to the radiator end tank is a special length and should be the ONLY bolt used upon reinstallation.

15. Remove the 2 condenser to radiator mounting bolts.
16. Separate the condenser from the radiator by lifting out of the lower mounting tabs.



17. Remove the A/C condenser side seals (1).
18. Remove the condenser from the vehicle.

1. Add the proper amount of refrigerant oil to the new condenser. Refer to Refrigerant System Capacities .

Important: Install the condenser into the lower radiator mounting tabs.

2. Install the condenser into the vehicle.

Notice: The bolt retaining the condenser to the radiator end tank is a special length and should be the ONLY bolt used upon reinstallation. The use of a longer bolt will damage the radiator end tank.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Install the condenser mounting bolts.

Tighten
Tighten the bolts to 6 N·m (53 lb in).




4. Install the new A/C condenser side seals (1).



5. Reposition the headlamp and bumper fascia support and install the fasteners (1).

Tighten
Tighten the bolt and the nut to 9 N·m (80 lb in).




6. Install the lower hood latch support bolts (1).

Tighten
Tighten the bolts to 9 N·m (80 lb in).




7. Install a new sealing washer to the evaporator hose. Refer to Sealing Washer Replacement .
8. Install the evaporator hose to the condenser.
9. Install the evaporator hose nut condenser.

Tighten
Tighten the nut to 20 N·m (12 lb ft).




10. Install a new sealing washer to the compressor hose. Refer to Sealing Washer Replacement .
11. Install the compressor hose to the condenser.
12. Install the compressor hose nut to the condenser.

Tighten
Tighten the nut to 20 N·m (15 lb ft).




13. Install the upper radiator mounting brackets.
14. Install the upper radiator mounting bracket bolts.

Tighten
Tighten the bolts to 9 N·m (7 lb ft).




15. Install the upper radiator seal.
16. Install the headlamp and bumper fascia mounting panel support bracket bolts.

Tighten
Tighten the bolts to 9 N·m (80 lb in).

17. Install the headlamps. Refer to Headlamp Replacement in Lighting Systems.
18. Evacuate and recharge the A/C system. Refer to Refrigerant Recovery and Recharging .
19. Leak test the fittings of the component using the J 39400-A .

Air Conditioning Condenser Replacement LD8

Tools Required

J 39400-A Halogen Leak Detector

1. Recover the refrigerant. Refer to Refrigerant Recovery and Recharging .
2. Remove the upper tie bar . Refer to Front End Upper Tie Bar Replacement in Body Front End.
3. Remove the headlamps. Refer to Headlamp Replacement in Lighting Systems.



4. Remove the upper radiator seal.



5. Remove the discharge hose to condenser nut.
6. Remove the discharge hose from the condenser.
7. Remove the evaporator hose to condenser nut.



8. Remove the evaporator hose from the condenser.
9. Remove and discard the sealing washers from the compressor hose and the evaporator hose.



10. Remove the lower hood latch support bolts (1).

Important: The bolt retaining the condenser to the radiator end tank is a special length and should be the ONLY bolt used upon reinstallation.

11. Remove the 2 condenser to radiator mounting bolts.
12. Separate the condenser from the radiator by lifting out of the lower mounting tabs.



13. Remove the A/C condenser side seals (1).
14. Remove the condenser from the vehicle.

1. Add the proper amount of refrigerant oil to the new condenser. Refer to Refrigerant System Capacities .

Important: Install the condenser into the lower radiator mounting tabs.

2. Install the condenser into the vehicle.

Notice: The bolt retaining the condenser to the radiator end tank is a special length and should be the ONLY bolt used upon reinstallation. The use of a longer bolt will damage the radiator end tank.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Install the condenser mounting bolts.

Tighten
Tighten the bolts to 6 N·m (53 lb in).




4. Install the new A/C condenser side seals (1).



5. Install the lower hood latch support bolts (1).

Tighten
Tighten the bolts to 9 N·m (80 lb in).




6. Install a new sealing washer to the evaporator hose. Refer to Sealing Washer Replacement .
7. Install the evaporator hose to the condenser.
8. Install the evaporator hose nut.

Tighten
Tighten the nut to 20 N·m (12 lb ft).




9. Install a new sealing washer to the discharge hose. Refer to Sealing Washer Replacement .
10. Install the discharge hose to the condenser.
11. Install the discharge hose nut.

Tighten
Tighten the nut to 20 N·m (15 lb ft).




12. Install the upper radiator seal.
13. Install the upper tie bar. Refer to Front End Upper Tie Bar Replacement in Body Front End.
14. Install the headlamps. Refer to Headlamp Replacement in Lighting Systems.
15. Evacuate and recharge the A/C system. Refer to Refrigerant Recovery and Recharging .
16. Leak test the fittings of the component using the J 39400-A .