DTC P1585 3.8L
Circuit Description
Output driver modules (ODMs) are used by the powertrain control module (PCM) in order to turn on many of the current-driven devices that are needed to control various engine and transaxle functions. DTC P1558 set indicates that an improper voltage level has been detected on the output circuit which controls the cruise control inhibit circuit.
Conditions for Running the DTC
| • | The engine speed is 450 RPM or more. |
| • | System voltage is between 8 and 16 volts. |
Conditions for Setting the DTC
| • | The ignition is ON. |
| • | The PCM detects an improper voltage level on the cruise inhibit signal circuit. |
| • | The condition exists for at least 30 seconds. |
Action Taken When the DTC Sets
| • | The PCM will not illuminate the malfunction indicator lamp (MIL). |
| • | The PCM will store the conditions present when the DTC set as Failure Records data only. |
Conditions for Clearing the DTC
| • | The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | The DTC can be cleared by using the scan tool's Clear DTC Information function. |
Diagnostic Aids
In order to determine whether an improper voltage level exists on the output circuit, the PCM compares the voltage level to the commanded state.
If the condition is intermittent, refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
Normally, ignition positive voltage should be present on the control circuit with the PCM disconnected and the ignition turned ON.
-
Tests for short to voltage on the control circuit.
-
This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is being replaced, the new PCM must be programmed.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Schematic Reference: Cruise Control Schematics | ||||
1 | Did you perform the Cruise Control Diagnostic System Check ? | -- | Go to Step 2 | |
Does the voltage measure near the specified value? | B+ | Go to Step 3 | Go to Step 4 | |
Does the test lamp illuminate? | -- | Go to Step 7 | Go to Step 5 | |
4 | Test the cruise control inhibit signal circuit for a open, high resistance or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 6 |
5 | Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 8 |
6 | Inspect for poor connections at the harness connector of the cruise control module. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 9 |
7 | Repair the short to voltage in the cruise control inhibit signal circuit. Did you complete the repair? | -- | Go to Step 10 | -- |
|
Important: The replacement powertrain control module (PCM) must be programmed. Refer to Service Programming System (SPS) in Programming. Replace the PCM. Refer to Powertrain Control Module Replacement in Engine Controls. Did you complete the replacement? | -- | Go to Step 10 | -- | |
9 | Replace the cruise control module. Refer to Cruise Control Module Replacement . Did you complete the replacement? | -- | Go to Step 10 | -- |
10 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
DTC P1585 4.6L
Circuit Description
Output driver modules (ODMs) are used by the powertrain control module (PCM) in order to turn on many of the current-driven devices that are needed to control various engine and transaxle functions. DTC P1585 set indicates that an improper voltage level has been detected on the output circuit which controls the cruise control inhibit circuit.
Conditions for Running the DTC
| • | The engine speed is 450 RPM or more. |
| • | System voltage is between 8-16 volts. |
Conditions for Setting the DTC
| • | The ignition is ON. |
| • | The PCM detects an improper voltage level on the cruise control inhibit signal circuit. |
| • | The condition exists for at least 30 seconds. |
Action Taken When the DTC Sets
| • | The PCM will not illuminate the malfunction indicator lamp (MIL). |
| • | The PCM will store the conditions present when the DTC sets as Fail Records data only. |
Conditions for Clearing the DTC
| • | The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | The DTC can be cleared by using the scan tool's Clear DTC Information function. |
Diagnostic Aids
In order to determine whether an improper voltage level exists on the output circuit, the PCM compares the voltage level to the commanded state.
If the condition is intermittent, refer to Testing for Intermittent Conditions and Poor Connections Intermittent Conditions in Wiring Systems.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
Normally, ignition positive voltage should be present on the signal circuit with the PCM disconnected and the ignition turned ON.
-
Tests for a short to voltage on the control circuit.
-
This vehicle is equipped with a PCM which utilizes an electrically erasable programmable read only memory (EEPROM). When the PCM is being replaced, the new PCM must be programmed.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Schematic Reference: Cruise Control Schematics | ||||
1 | Did you perform the Cruise Control Diagnostic System Check ? | -- | Go to Step 2 | |
Does the voltage measure near the specified value? | B+ | Go to Step 3 | Go to Step 4 | |
Does the test lamp illuminate? | -- | Go to Step 7 | Go to Step 5 | |
4 | Test the cruise control inhibit signal circuit for a short to ground. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 6 |
5 | Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 8 |
6 | Inspect for poor connections at the harness connector of the cruise control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 9 |
7 | Repair the short to voltage in the cruise control inhibit signal circuit. Refer to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | -- |
|
Important: The replacement PCM must be programmed. Replace the PCM. Refer to Powertrain Control Module Replacement in Engine Controls - 4.6L. Did you complete the replacement? | -- | Go to Step 10 | -- | |
9 | Replace the cruise control module. Refer to Cruise Control Module Replacement . Did you complete the replacement? | -- | Go to Step 10 | -- |
10 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
