GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 2001 🢒 Bonneville 🢒 Body and Accessories 🢒 Doors 🢒 Power Window Inoperative - Passenger Door

Test Description

The Numbers below refer to the step numbers on the diagnostic table.

  1. This step checks to see that the door module associated with the inoperative window recognizes the switch input.

    Enabling the headlamps in this step elliminates the possibility of the window switch using an alternative path to ground through the switch illumination circuit, which could cause the scan tool to display incorrect window switch states.

    2.

  2. This step determines if the Express Down function of the window switch (if applicable) has failed.

    3.

  3. This step eliminates the door module battery positive voltage and ground circuits (associated with module connector C3 for the front passenger door, or, associated with module connector C2 for a rear door) as the cause.

    4.

  4. This step eliminates the window switch as the cause of the malfunction.

    If the 3 amp jumper wire fuse opens when the jumper wire is connected, test the signal circuit of the inoperative state for a short to battery positive voltage.

    5.

  5. This step eliminates the switch ground circuit as the cause.

    6.

  6. This step eliminates the switch Up or Down signal circuits as the cause.

Step

Action

Yes

No

Schematic Reference: Power Window Schematics and Door Control Module Schematics

1

Did you Perform the Door Systems Diagnostic System Check?

Go to Step 2

Go to Diagnostic System Check - Door Systems

2

Verify that the Power Windows Inoperative-Passenger Door complaint is present.

Do the passenger door windows operate as described in the Description and Operation?

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 3

3

  1. With the scan tool, select the Driver Door Module, Data Display, Inputs list.
  2. With the scan tool, observe the appropriate Door Window Sw. parameter for the inoperative window (Pass Door Window Sw, Lt Rear Door Window Sw, or Rt Rear Door Window Sw).
  3. Turn ON the headlamps switch.
  4. Operate the passenger door window switch of the inoperative window to both the Up and Down positions.
  5. If applicable, operate the passenger door window switch of the inoperative window to the Express Down position.

Did the Door Window Sw. parameter change from the Idle state to the Up, Down, and, if applicable, Express Down states as expected?

Go to Step 5

Go to Step 4

4

Is Express Down the only inoperative state?

Go to Step 15

Go to Step 9

5

  1. Turn OFF the ignition.
  2. Disconnect the 4 pin harness connector from the door module that is associated with the inoperative window (module connector C3 for the front passenger door, or, module connector C2 for a rear door).
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a test lamp between the battery positive voltage circuit and the ground circuit of the connector.

Does the test lamp illuminate?

Go to Step 6

Go to Step 10

6
  1. Turn OFF the ignition.
  2. Connect the 4 pin harness connector (C3 for the front passenger door, or, C2 for a rear door)
  3. Disconnect the harness connector of the window motor associated with the inoperative window.
  4. Turn ON the ignition, with the engine OFF.
  5. Connect a test lamp between the power window motor Up circuit of the harness connector and a good ground.
  6. Operate the passenger door window switch associated with the inoperative window to the Up position.

Does the test lamp illuminate?

Go to Step 7

Go to Step 11

7
  1. Connect a test lamp between the power window motor Down circuit of the harness connector and a good ground.
  2. Operate the passenger door window switch associated with the inoperative window to the Down position.

Does the test lamp illuminate?

Go to Step 8

Go to Step 12

8
  1. Connect a test lamp between the power window motor Up circuit and the power window motor Down circuit of the harness connector.
  2. Operate the passenger door window switch associated with the inoperative window to both the Up and Down positions.

Does the test lamp illuminate for both the Up and Down positions?

Go to Step 16

Go to Step 17

9

  1. Turn OFF the ignition.
  2. Disconnect the power window switch harness connector of the window that did not operate.
  3. Install a 3 amp fused jumper wire in the harness connector, between the switch ground circuit and the switch signal circuit of the inoperative window state.
  4. Turn ON the ignition, with the engine OFF.

Does the Door Window Sw. parameter indicate the inoperative state?

Go to Step 15

Go to Step 13

10

Test the battery positive voltage circuit (associated with connector C3 for the front passenger door, or, connector C2 for a rear door) for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 18

11

Test the power window motor Up circuit for a short to ground, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 17

12

Test the power window motor Down circuit for a short to ground, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 17

13

Test the power window switch ground circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 14

14

Test the power window switch signal circuit, of the inoperative window state for a short to battery or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 17

15

Inspect for poor connections at the harness connector of the inoperative power window switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 19

16

Inspect for poor connections at the harness connector of the inoperative power window motor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 20

17

Inspect for poor connections at the harness connector of the inoperative passenger door module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 21

18

Repair the open ground circuit (associated with connector C3 for the front passenger door, or, connector C2 for a rear door) of the module. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 22

--

19

Replace the inoperative power window switch. Refer to Rear Side Door Window Switch Replacement or Front Door Switch Replacement .

Did you complete the replacement?

Go to Step 22

--

20

Replace the inoperative power window motor. Refer to Power Window Motor Replacement .

Did you complete the replacement?

Go to Step 22

--

21

Replace the inoperative passenger door module. Refer to Door Control Module Replacement .

Did you complete the replacement?

Go to Step 22

--

22

Operate the system in order to verify the repair.

Did you correct the condition?

System OK

Go to Step 2