Circuit Description
The instrument panel integration module (IPM) monitors the ambient light on the left and right side of the vehicle via a light sensitive photodiode which is called a sunload sensor assembly. The IPM uses this information to compensate for the effect of the sun on the inside air temperature of the vehicle. When the sensor is in direct sunlight, the signal voltage is low. When the sensor is shaded, the signal voltage is high. The IPM requests A/C compressor clutch engagement and controls the air temperature door positions in order to maintain the selected air temperature on the HVAC control module.
Conditions for Running the DTC
The ignition is turned ON.
Conditions for Setting the DTC
The IPM detects the signal circuit is less than 0.09 volt (5 counts) or greater than 4.90 volts (250 counts).
Action Taken When the DTC Sets
A default value of 0 counts will be substituted for the solar sensor data by the IPM. The Left Solar or Right Solar displayed on the scan tool in the HVAC Sensors data list will be the default value. The Left Solar Sensor or Right Solar Sensor displayed on the scan tool in the Open/Short Data list will be the actual value.
Conditions for Clearing the DTC
| • | The DTC will become history if the IPM no longer detects a failure. |
| • | The history DTC will clear after 50 fault free ignition cycles. |
| • | The DTC can be cleared with a scan tool. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
When diagnosing using this table, DTC B0184 is for the left sunload sensor. DTC B0189 is for the right sunload sensor. Follow the table for the corresponding circuits for that DTC.
-
Tests for the proper operation of the circuit in the high voltage range.
-
Tests for the proper operation of the circuit in the low voltage range. If the fuse in the jumper opens when you perform this test, the signal circuit is shorted to voltage.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: HVAC Schematics | ||||
1 | Did you perform the HVAC Diagnostic System Check? | -- | Go to Step 2 | |
Does the scan tool indicate that the Solar Sensor parameter is with in the specified range? | 0.09-4.90 V | Go to Testing for Intermittent Conditions and Poor Connections | Go to Step 3 | |
Does the scan tool indicate that the Solar Sensor parameters are greater than the specified value? | 4.90 V | Go to Step 4 | Go to Step 5 | |
Does the scan tool indicate that the Solar Sensor parameter is less than the specified value? | 0.09 V | Go to Step 8 | Go to Step 6 | |
5 | Test the right or left sunload sensor signal circuit of the sunload sensor assembly for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 9 |
6 | Test the right or left sunload sensor signal circuit of the sunload sensor assembly for a short to voltage, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 7 |
7 | Test the low reference circuit of the sunload sensor assembly for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 9 |
8 | Inspect for poor connections at the harness connector of the sunload sensor assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 10 |
9 | Inspect for poor connections at the harness connector of the instrument panel integration module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 11 |
10 | Replace the sunload sensor assembly. Refer to Sunload and Twilight Sentinel Sensor Replacement in Instrument Panel, Gauges and Console. Did you complete the replacement? | -- | Go to Step 12 | -- |
11 |
Important: : Perform the recalibration procedure for the instrument panel integration module. Replace the instrument panel integration module. Refer to Instrument Panel Module Replacement in Body Control System. Did you complete the replacement? | -- | Go to Step 12 | -- |
12 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
