Exhaust System Insulator, Hanger, Bracket Replacement Converter

1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

Notice: Refer to Catalytic Converter Movement Notice in the Preface section.

2. Suitably support the exhaust system.



3. Remove the three-way catalytic converter hangers.
4. Inspect the three-way catalytic converter brackets for serviceability. Repair or replace as necessary.

1. Install the three-way catalytic converter hangers.
2. Remove the support from the exhaust system and vehicle.
3. Inspect for leaks and underbody contact.
4. Lower the vehicle.

Exhaust System Insulator, Hanger, Bracket Replacement Muffler Front

1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

Notice: Refer to Catalytic Converter Movement Notice in the Preface section.

2. Suitably support the exhaust system.



3. Remove the exhaust pipe hanger bracket insulator.
4. Inspect the exhaust muffler front hanger bracket for serviceability. Repair or replace as necessary.

1. Install the front exhaust pipe hanger bracket insulator.
2. Remove the support from the exhaust system.
3. Inspect for leaks and underbody contact.
4. Lower the vehicle.

Exhaust System Insulator, Hanger, Bracket Replacement Muffler Center

1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

Notice: Refer to Catalytic Converter Movement Notice in the Preface section.

2. Suitably support the exhaust system.



3. Remove the exhaust pipe center hanger insulator.



4. Inspect the exhaust pipe center hanger bracket for serviceability. Repair or replace as necessary.
5. Remove the exhaust pipe center hanger bolt.
6. Remove the exhaust pipe center hanger bracket.

1. Replace the exhaust pipe center hanger bracket if removed.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the exhaust pipe center hanger bolt.

Tighten
Tighten the exhaust pipe center hanger bolt to 25 N·m (18 lb ft).




3. Install the exhaust pipe rear hanger insulator.
4. Remove the support from the exhaust system.
5. Inspect for leaks and underbody contact.
6. Lower the vehicle.

Exhaust System Insulator, Hanger, Bracket Replacement Muffler Rear

1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

Notice: Refer to Catalytic Converter Movement Notice in the Preface section.

2. Suitably support the exhaust system.



3. Remove the exhaust muffler rear hanger insulators.



4. Inspect the exhaust muffler rear hanger bracket for serviceability. Repair or replace as necessary.
5. Remove the rear bumper impact bar bolts.
6. Remove the exhaust muffler rear hanger bracket.

1. Replace the exhaust muffler rear hanger bracket if removed.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the rear bumper impact bar bolts.

Tighten
Tighten the rear bumper impact bar bolts to 25 N·m (18 lb ft).




3. Install the exhaust muffler rear hanger insulators.
4. Remove the support from the exhaust system.
5. Inspect the leaks and underbody contact.
6. Lower the vehicle.