Tools Required

J 39232 Wiper Transmission Separator

1. Remove the wiper arms from the wiper transmission drive shafts. Refer to Windshield Wiper Arm Replacement .
2. Remove the air inlet grille panel from the vehicle. Refer to Air Inlet Grille Panel Replacement .

Remove the connector from the wiper motor.

3. Remove the wiper transmission from the wiper motor crank arm using the J 39232 Wiper Transmission Separator.



4. Remove three screws and the wiper drive system module from the vehicle.



5. Remove the wiper motor crank arm from the wiper motor.

5.1.	Remove the rubber boot from the wiper motor crank arm.

5.2.	Loosen the screw.

5.3.	Tap on the screw with a soft-faced mallet while holding up on the wiper motor crank arm until the wiper motor crank arm is loose on wiper motor.

5.4.	Remove the screw and wiper motor crank arm from wiper motor.




6. Remove three screws and wiper motor from wiper drive system module.
7. Remove the shaft seal and the water shield from the wiper motor.

Tools Required

J 39529 Wiper Transmission Installer

1. Install the water shield and shaft seal on the wiper motor.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the wiper motor on the wiper drive system module with three screws.

Tightening
Tighten three screws to 7 N·m (62 lb in).




3. Install the wiper motor crank arm on the wiper motor.

3.1.	Install the connector to the wiper motor.

3.2.	Turn the ignition switch to the ACCY position.

3.3.	Set the wiper switch to the PULSE position. The wiper motor should be operating.

3.4.	Turn the ignition off when the wiper motor is in the innerwipe position and not moving.

3.5.	Disconnect the connector from the wiper motor.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3.6.	Install the wiper motor crank arm on the wiper motor while maintaining a 4-8 mm (0.157-0.314 in) gap between wiper motor crank arm and bracket tab.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3.7.	Install the screw.

3.8.	Check the gap between wiper motor crank arm and bracket tab. If the gap is not 4-8 mm (0.157-0.314 in), remove the crank arm and repeat installation.

Tighten
Tighten the screw to 16 N·m (142 lb in).

3.9.	Install the rubber boot onto the wiper motor crank arm.





Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install the wiper drive system module on the vehicle with three screws.

Tighten
Tighten the screws to 10 N·m (88 lb in).




5. Install the wiper transmission on the wiper motor crank arm using the J 39529 Wiper Transmission Installer.
6. Install the connector onto the wiper motor.
7. Install the air inlet grille panel on the vehicle. Refer to Air Inlet Grille Panel Replacement .
8. Install the wiper arms onto the wiper transmission drive shaft.
9. Operate the wipers and check for proper operation.