GM Service Manual Online
For 1990-2009 cars only

Object Number: 13321  Size: LF
Engine Controls Components
Ignition Control (IC) Module
OBD II Symbol Description Notice
ESD Notice
ESD Notice

Circuit Description

Under normal system operation when the key is turned ON and until engine rpm is high enough for the PCM to control spark, the PCM will open the bypass circuit (CKT 424) to the Ignition Control Module, the IC module will then ground the Ignition Control circuit (CKT 423). This is called module mode because the IC module is controlling spark. Once the engine speed is high enough, about 65 rpm, 4X reference pulses are received and no PCM faults are detected the PCM will close the bypass line and in response the IC module will unground the IC circuit, this allows PCM control of spark. This is called the ignition control mode. This diagnostic test is used to check for faults in both the bypass circuit and the IC circuit. To check both circuits this diagnostic runs two tests, one during crank and one while running. If Ignition Control pulses are detected by the PCM on the IC line while in module mode, cranking, or if no Ignition Control pulses are detected by the PCM while in ignition control mode, running, DTC P1350 will set.

Conditions for Setting the DTC

Test Conditions

    •  Cranking test.
       -  DTC P1376 not set.
       -  At least 1 4X reference pulse has been received by the PCM.
    •  Running test.
       -  DTC P0322 and P1376 not set.
       -  At least 1 4X reference pulse has been received by the PCM.

Failure Conditions

    •  Cranking test.
         Ignition Control pulses are received by the PCM when cranking or running test has failed THIS ignition cycle.
    •  Running test.
        No Ignition Control pulses are received by the PCM while engine is running.

Action Taken When the DTC Sets

    •  PCM ignition control is disabled for ignition cycle.
    •  PCM disables EGR.
    •  Transaxle shift adapts are maintained at current levels.
    •  The PCM will illuminate the malfunction indicator lamp (MIL) when the diagnostic runs and fails.
    •  The PCM will record operating conditions at the time the diagnostic fails. This information will be stored in the Freeze Frame and Failure Records.

Conditions for Clearing the MIL/DTC

    •  The PCM will turn the MIL OFF after three consecutive drive trips that the diagnostic runs and does not fail.
    •  A Last Test Failed (current) DTC will clear when the diagnostic runs and does not fail.
    •  A History DTC will clear after forty consecutive warm-up cycles with no failures of any emission related diagnostic test.
    • Use a scan tool to clear DTCs.
    • Interrupting PCM battery voltage may or may not clear DTCs. This practice is not recommended. Refer to Clearing Diagnostic Trouble Codes in PCM Description and Operation.

Diagnostic Aids

If fault is not present check terminal contact at the IC module and PCM connectors.

Test Description

  1. When checking for shorts to ground, resistance of more than 10K ohms is usually acceptable although most readings should be infinite (OL).

    When checking for circuit continuity (opens) resistance should be 5 ohms or less.

    When checking for shorts to voltage take measurements with the ignition ON and OFF.

    Disconnect the circuit from all components before performing any circuit check.

    Always check or zero the meter before performing resistance checks.

  2. A diagnostic jumper can be created with the terminals supplied in the J 38125-A Terminal Repair Kit. Assemble the jumpers and terminals and cover the exposed terminals with heat shrink tubing. Do not cover the spade of the male terminals.

    If the vehicle stalls during this step turn the ignition OFF and wait 30 seconds then restart the engine before attempting to measure the circuit voltage.

  3. If the vehicle stalls during this step turn the ignition OFF and wait 30 seconds then restart the engine before attempting to measure the circuit voltage.

Step

Action

Value(s)

Yes

No

1

Was the Powertrain On-Board Diagnostic (OBD) System Check performed?

--

Go to Step 2

Go to the A Powertrain On Board Diagnostic (OBD) System Check

2

Are DTC's P0322, P0372, P1323, P1371, P1375 or P1376 also set?

--

Go to DTC (s) that are set

Go to Step 3

3

  1. Turn the ignition OFF
  2. Wait 30 seconds.
  3. Turn the ignition ON but do not crank the engine.
  4. Using the scan tool store the snapshot info for DTC P1350 and then clear DTC P1350.
  5. After clearing the DTC start and idle the engine.

Does P1350 fail this ignition?

--

Go to Step 4

Fault not present. Refer to Diagnostic Aids

4

  1. Record the fluid life indexes.
  2. Turn the ignition OFF.
  3. Wait 30 seconds.
  4. Disconnect PCM connector C2 and IC Module connector C4.
  5. Using the DMM J 39200 check the Bypass and Ignition Control circuits for high resistance, shorts to ground, shorts to voltage and shorts to other circuits. Refer to Test Descriptions .
  6. Repair circuits as needed.

Was a repair made to any circuit?

--

Verify Repair

Go to Step 5

5

  1. Reconnect PCM connector C2.
  2. Turn the ignition ON but DO NOT crank the engine.
  3. Using the DMM measure the DC voltage to ground on the Bypass circuit and then the Ignition Control circuit.

Is the voltage less than the value specified?

1.0 volts

Go to Step 6

Go to Step 11

6

  1. Turn the ignition OFF.
  2. Wait 30 seconds.
  3. Install diagnostic jumper at IC module C4.
  4. OR:

    • Jumper C4 terminal A to module pin A.
    • Jumper C4 terminal B to module pin B.
    • Jumper C4 terminal C to module pin C.
    • Jumper C4 terminal D to module pin D.
    • Jumper C4 terminal E to module pin E.
    • Jumper C4 terminal F to module pin F.
  5. Disconnect the Ignition Control and Bypass circuit jumpers (terminals D and E). Ensure jumpers are away from contacting other circuits, engine ground or each other.
  6. Start and idle the engine.
  7. Measure the DC voltage to ground on the Ignition Control circuit FROM the PCM.

Is the voltage fixed near the value specified?

1.7 volts

Go to Step 7

Go to Step 11

7

Measure the DC voltage to ground on the Bypass circuit FROM the PCM.

Is the voltage less than the value specified?

1.0 volts

Go to Step 8

Go to Step 11

8

  1. Momentarily ground the Ignition Control circuit.
  2. Measure the DC voltage to ground on the Bypass circuit FROM the PCM.

Is the voltage the same or more than the value specified?

4.7 volts

Go to Step 9

Go to Step 11

9

  1. Check terminal contact at the IC Module connector C4.
  2. Repair terminal contact if needed.

Was terminal contact repaired?

--

Verify Repair

Go to Step 10

10

Replace the Ignition Control Module. Refer to Ignition Control Module Replacement (Assembly) .

Is the replacement complete?

--

Verify Repair

--

11

  1. Check terminal contact at PCM connector C2.
  2. Repair terminal contact if needed.

Was terminal contact repaired?

--

Verify Repair

Go to Step 12

12

Replace the PCM. Refer to PCM Replacement/Programming .

Is the replacement complete?

--

Verify Repair

--