Power Steering Pump Replacement 2.2L

Tools Required

J 25034-C Power Steering Pump Pulley Remover

1. Remove the upper fan shroud. Refer to Fan Shroud Replacement in Engine Cooling.
2. Place a drain pan below the pump.



3. Remove the power steering hoses from the power steering pump.
4. Cap the power steering hoses.
5. Remove the drive belt. Refer to Drive Belt Replacement in Engine Mechanical 2.2L.



6. Install J 25034-C to the power steering pump pulley.

Ensure that the pilot bottoms in the pump shaft by turning the nut to the top of the pilot bolt.

7. Hold the pilot bolt.
8. Turn the nut clockwise.



9. Remove the power steering pump pulley.



10. Disconnect the A/C compressor electrical connection.



11. Remove the A/C compressor mounting bolts.
12. Remove the A/C compressor rear bracket mounting bolts.
13. Remove the A/C compressor from the brackets and set aside.



14. Remove the power steering pump front mounting bolts.
15. Remove the power steering pump rear mounting bracket nuts from the engine studs.
16. Remove the power steering pump rear mounting bracket bolt.
17. Remove the power steering pump.

Tools Required

J 25033-C Power Steering Pump Pulley Installer

1. Install the power steering pump.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the front mounting bolts.

Tighten
Tighten the power steering pump front mounting bolts to 30 N·m (22 lb ft).

3. Install the power steering pump rear mounting bracket bolt.
4. Install the power steering pump rear mounting bracket nuts to the engine studs.

Tighten
Tighten the power steering pump rear mounting bracket bolt and nuts to 50 N·m (37 lb ft).




5. Install the A/C compressor to the accessory bracket.
6. Install the A/C compressor rear bracket mounting bolts.

Tighten
Tighten the A/C compressor rear bracket mounting bolts to 31 N·m (23 lb ft).

7. Install the A/C compressor mounting bolts.

Tighten
Tighten the A/C compressor mounting bolts to 50 N·m (37 lb ft).




8. Connect the A/C compressor electrical connection.



9. Place the pulley on the end of the power steering pump shaft.



10. Install the J 25033-C .

Ensure that the pilot bolt bottoms in the shaft by turning the nut to the top of the pilot bolt.

11. Hold the pilot bolt.
12. Turn the nut counterclockwise.
13. Install the power steering pump pulley.



14. Install the pulley flush against the end of the power steering pump shaft, with an allowable variance of 0.25 mm (0.010 in).
15. Install the drive belt. Refer to Drive Belt Replacement in Engine Mechanical 2.2L.



16. Install the power steering pump hoses.
17. Install the upper fan shroud. Refer to Fan Shroud Replacement in Engine Cooling.
18. Fill the power steering system.
19. Bleed the system.

Refer to Power Steering System Bleeding .

20. Inspect the hoses for clearance away from the frame and other components.

Power Steering Pump Replacement 4.3L

Tools Required

J 25034-C Power Steering Pump Pulley Remover

1. Remove the upper fan shroud. Refer to Fan Shroud Replacement in Engine Cooling.
2. Remove the drive belt. Refer to Drive Belt Replacement in Engine Mechanical 4.3L.
3. Remove the fan clutch from the water pump. Refer to Fan Clutch Replacement in Engine Cooling.



4. Install J 25034-C to the power steering pump pulley.

Ensure that the pilot bottoms in the pump shaft by turning the nut to the top of the pilot bolt.

5. Hold the pilot bolt.
6. Turn the nut clockwise.



7. Remove the power steering pump pulley.
8. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
9. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage.
10. Place a drain pan below the pump.
11. Disconnect the power steering pressure hose from the power steering pump.
12. Lower the vehicle.



13. Disconnect the power steering return hose from the power steering pump.
14. Cap the power steering pump hoses.



15. Remove the filler neck tube mounting bolt.
16. Remove the filler neck tube.



17. Remove the power steering pump rear mounting bracket nut from the engine stud.
18. Remove the power steering pump lower mounting nut from the engine stud.



19. Remove the power steering pump front mounting bolts.
20. Remove the power steering pump.

Tools Required

J 25033-C Power Steering Pump Pulley Installer

1. Install the power steering pump.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the power steering pump front mounting bolts.

Tighten
Tighten the power steering pump front mounting bolts to 50 N·m (37 lb ft).




3. Install the power steering pump rear mounting bracket nut to the engine stud.
4. Install the power steering pump lower mounting nut to the engine stud.

Tighten
Tighten the power steering pump rear mounting bracket nut and the lower mounting nut to 41 N·m (31 lb ft).




5. Install the filler neck tube.
6. Install the filler neck tube mounting bolt.

Tighten
Tighten the filler neck tube mounting bolt to 20 N·m (15 lb ft).




7. Connect the power steering return hose to the power steering pump.
8. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
9. Connect the power steering pressure hose to the power steering pump.
10. Install the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage.
11. Lower the vehicle.



12. Place the power steering pump pulley on the end of the power steering pump shaft.



13. Install J 25033-C .

Ensure that the pilot bolt bottoms in the shaft by turning the nut to the top of the pilot bolt.

14. Hold the pilot bolt.
15. Turn the nut counterclockwise.
16. Install the power steering pump pulley.



17. Install the pulley (1) flush against the end of the power steering pump shaft (2), with an allowable variance of 0.25 mm (0.010 in).
18. Install the fan clutch to from the water pump. Refer to Fan Clutch Replacement in Engine Cooling.
19. Install the drive belt. Refer to Drive Belt Replacement in Engine Mechanical 4.3L.
20. Install the upper fan shroud. Refer to Fan Shroud Replacement in Engine Cooling.
21. Fill the power steering system.
22. Bleed the system. Refer to Power Steering System Bleeding .
23. Inspect the hoses for clearance away from the frame and other components.