DTC P0758 2-3 Shift Solenoid Circuit Electrical 2.2L
| Table 1: | Shift Solenoid Valve State and Gear Ratio 4L60-E |
| Table 2: | DTC P0758 2-3 Shift Solenoid Circuit -- Electrical (2.2L) |
Circuit Description
The 2-3 Shift Solenoid Valve (2-3 SS Valve) controls the fluid flow acting on the 2-3 shift valves. The 2-3 SS Valve is a normally-open exhaust valve that is used with the 1-2 Shift Solenoid Valve in order to allow four different shifting combinations. The solenoid attaches to the control valve body within the transmission. The 2-3 SS Valve receives ignition voltage through circuit 1020. The Powertrain Control Module (PCM) controls the solenoid by providing the ground path on circuit 1223.
When the PCM detects a continuous open or short to ground in the 2-3 SS Valve circuit or the 2-3 SS Valve, then DTC P0758 sets. DTC P0758 is a type A DTC.
Conditions for Setting the DTC
| • | The system voltage is 8-16 volts. |
| • | The engine speed is 450 RPM for 5 seconds. |
| • | Not in fuel cutoff. |
| • | All of the above conditions are met for 5 seconds and either of the following fail conditions occurs for 5 seconds. |
| - | The PCM commands the solenoid ON and the voltage input remains high (B+). |
| - | The PCM commands the solenoid OFF and the voltage input remains low (0 volts). |
Action Taken When the DTC Sets
| • | The PCM illuminates the Malfunction Indicator Lamp (MIL). |
| • | The PCM commands third gear only. |
| • | The PCM commands maximum line pressure. |
| • | The PCM inhibits TCC engagement. |
| • | The PCM freezes shift adapts from being updated. |
| • | DTC P0758 stores in PCM history. |
Conditions for Clearing the MIL/DTC
| • | The PCM turns OFF the MIL after three consecutive trips without a failure reported. |
| • | A scan tool can clear the DTC from the PCM history. The PCM clears the DTC from the PCM history if the vehicle completes 40 warm-up cycles without a failure reported. |
| • | The PCM cancels the DTC default actions when the fault no longer exists and the ignition is OFF long enough in order to power down the PCM. |
Diagnostic Aids
| • | Inspect the wiring at the PCM, the transmission connector and all other circuit connecting points for the following conditions: |
| - | A bent terminal |
| - | A backed out terminal |
| - | A damaged terminal |
| - | Poor terminal tension |
| - | A chafed wire |
| - | A broken wire inside the insulation |
| - | Moisture intrusion |
| - | Corrosion |
| • | When diagnosing for an intermittent short or open condition, massage the wiring harness while watching the test equipment for a change. |
Gear | 1-2 Shift Solenoid | 2-3 Shift Solenoid | Gear Ratio |
|---|---|---|---|
1 | ON | ON | 3.059:1 |
2 | OFF | ON | 1.625:1 |
3 | OFF | OFF | 1.000:1 |
4 | ON | OFF | 0.696:1 |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests the function of the 2-3 SS Valve and the Automatic Transmission Wiring Harness Assembly (A/T Wiring Harness Assembly).
-
This step tests for power to the 2-3 SS Valve from the ignition through the fuse.
-
This step tests the ability of the PCM and the wiring to control the ground circuit.
-
This step measures the resistance of the A/T Wiring Harness Assembly and the 2-3 SS Valve.
Step | Action | Value(s) | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
1 | Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | Go to Powertrain OBD System Check in Engine Controls | |||||||
2 |
Important: Before clearing the DTC(s), use the scan tool in order to record the Freeze Frame and Failure Records for reference. Using the Clear Info function will erase the stored Freeze Frame and Failure Records from the PCM. Are DTCs P0740, P0753, P0785 and P1860 also set? | -- | ||||||||
3 |
Repair the circuit, the solenoids, and the harness if necessary. Refer to General Electrical Diagnosis Procedures in Wiring Systems. Did you find a short to ground condition? | -- | ||||||||
Using the transmission output control function on the scan tool, command the 2-3 SS Valve ON and OFF three times while listening to the bottom of the transmission pan (a stethoscope may be necessary). Does the solenoid click when commanded? | -- | Go to Diagnostic Aids | ||||||||
Is the test light ON? | -- | |||||||||
Is the test lamp ON when the 2-3 SS Valve is commanded ON and OFF when commanded OFF? | -- | |||||||||
7 | Repair the open or short to ground in ignition feed circuit 1020 (PNK) to the 2-3 SS Valve. Refer to General Electrical Diagnosis Procedures in Wiring Systems. Did you find and correct an open or short to ground condition? | -- | -- | |||||||
8 | Monitor the test lamp status. Was the test lamp OFF at all times? | -- | ||||||||
9 | Inspect circuit 1223 (YEL/BLK) of the engine wiring harness for an open or short to power. Repair the circuit if necessary. Refer to General Electrical Diagnosis Procedures in Wiring Systems. Did you find an open or short to power condition? | -- | ||||||||
10 | Was the test lamp ON at all times? | -- | -- | |||||||
11 | Inspect circuit 1223 (YEL/BLK) of the engine wiring harness for a short to ground. Repair the circuit if necessary. Refer to General Electrical Diagnosis Procedures in Wiring Systems. Did you find a short to ground condition? | -- | ||||||||
12 | Replace the PCM. Refer to PCM Replacement/Programming in Engine Controls. Is the replacement complete? | -- | -- | |||||||
Is the resistance within the specified range? | 19-31 ohms | |||||||||
14 |
Is the resistance within the specified range? | 19-31 ohms | ||||||||
15 | Using J 39200 DMM, measure the resistance between terminals B and E and ground. Are both readings greater than the specified value? | 250 K ohms | Go to Diagnostic Aids | |||||||
16 |
Are both readings greater than the value shown? | 250 K ohms | ||||||||
17 | Replace the A/T Wiring Harness Assembly. Refer to TCC PWM Solenoid, TCC Solenoid, and Wiring Harness Replacement. Is the replacement complete? | -- | -- | |||||||
18 | Replace the 2-3 SS Valve. Refer to Control and Shift Solenoids Replacement. Is the replacement complete? | -- | -- | |||||||
19 | In order to verify your repair, perform the following procedure:
Has the test run and passed? | -- | System OK |
DTC P0758 2-3 Shift Solenoid Circuit Electrical 4.3L
| Table 1: | Shift Solenoid Valve State and Gear Ratio 4L60-E |
| Table 2: | DTC P0758 2-3 Shift Solenoid Circuit -- Electrical (4.3L) |
Circuit Description
The 2-3 Shift Solenoid Valve (2-3 SS Valve) controls the fluid flow acting on the 2-3 shift valves. The solenoid is a normally-open exhaust valve. With the 1-2 Shift Solenoid Valve (1-2 SS Valve), the 2-3 SS Valve allows four different shifting combinations. The solenoid attaches to the control valve body within the transmission. The 2-3 SS Valve receives ignition voltage through circuit 1020. The Vehicle Control Module (VCM) controls the solenoid by providing the ground path on circuit 1223.
When the VCM detects a continuous open or short to ground in the 2-3 SS Valve circuit or the 2-3 SS Valve, then DTC P0758 sets. DTC P0758 is a type A DTC.
Conditions for Setting the DTC
| • | The system voltage is 10-16 volts. |
| • | The engine speed is greater than 450 RPM for 5 seconds. |
| • | Not in fuel cutoff. |
| • | All of the above conditions are met for 5 seconds and either of the following fail conditions occurs for 5 seconds: |
| - | The VCM commands the solenoid ON and the voltage input remains high (B+). |
| - | The VCM commands the solenoid OFF and the voltage input remains low (0 volts). |
Action Taken When the DTC Sets
| • | The VCM illuminates the Malfunction Indicator Lamp (MIL). |
| • | The VCM commands third gear only. |
| • | The VCM commands maximum line pressure. |
| • | The VCM inhibits TCC engagement. |
| • | The VCM freezes shift adapts from being updated. |
| • | DTC P0758 stores in VCM history. |
Conditions for Clearing the MIL/DTC
| • | The VCM turns OFF the MIL after three consecutive trips without a failure reported. |
| • | A scan tool can clear the DTC from the VCM history. The VCM clears the DTC from the VCM history if the vehicle completes 40 warm-up cycles without a failure reported. |
| • | The VCM cancels the DTC default actions when the fault no longer exists and the ignition is OFF long enough in order to power down the VCM. |
Diagnostic Aids
| • | Inspect the wiring at the VCM, the transmission connector and all other circuit connecting points for the following conditions: |
| - | A bent terminal |
| - | A backed out terminal |
| - | A damaged terminal |
| - | Poor terminal tension |
| - | A chafed wire |
| - | A broken wire inside the insulation |
| - | Moisture intrusion |
| - | Corrosion |
| • | When diagnosing for an intermittent short or open condition, massage the wiring harness while watching the test equipment for a change. |
Gear | 1-2 Shift Solenoid | 2-3 Shift Solenoid | Gear Ratio |
|---|---|---|---|
1 | ON | ON | 3.059:1 |
2 | OFF | ON | 1.625:1 |
3 | OFF | OFF | 1.000:1 |
4 | ON | OFF | 0.696:1 |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests the function of the 2-3 SS Valve and the Automatic Transmission Wiring Harness Assembly (A/T Wiring Harness Assembly).
-
This step tests for power to the 2-3 SS Valve from the ignition through the fuse.
-
This step tests the ability of the VCM and of the wiring to control the ground circuit.
-
This step measures the resistance of the A/T Wiring Harness Assembly and of the 2-3 SS Valve.
Step | Action | Value(s) | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
1 | Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | Go to Powertrain On Board Diagnostic (OBD) System Check in Engine Controls | |||||||
2 |
Important: Before clearing the DTC(s), use the scan tool in order to record the Freeze Frame and Failure Records for reference. Using the Clear Info function will erase the stored Freeze Frame and Failure Records from the VCM. Are DTCs P0740, P0753, P0785 and P1860 also set? | -- | ||||||||
3 |
Refer to General Electrical Diagnosis Procedures.
Did you find a short to ground condition? | -- | ||||||||
Using the transmission output control function on the scan tool, command the 2-3 SS Valve ON and OFF three times while listening to the bottom of the transmission pan (a stethoscope may be necessary). Did the solenoid click when commanded? | -- | Go to Diagnostic Aids | ||||||||
Is the test lamp ON? | -- | |||||||||
6 | Repair the open or short to ground in ignition feed circuit 1020 (PNK) to the 2-3 SS Valve. Refer to General Electrical Diagnosis Procedures. Did you find and correct an open or short to ground condition? | -- | -- | |||||||
Does the test lamp illuminate when you command the shift solenoid ON, and does the test lamp turn off when you command the shift solenoid OFF? | -- | |||||||||
8 |
Refer to General Electrical Diagnosis Procedures. Did you find an open, short to ground or short to power condition? | -- | ||||||||
9 | Replace the VCM. Refer to VCM Replacement/Programming in Engine Controls. Is the replacement complete? | -- | -- | |||||||
Is the resistance within the specified range? | 19-31 ohms | |||||||||
11 |
Is the resistance within the specified range? | 19-31 ohms | ||||||||
12 | Measure the resistance between terminals B and E and ground. Are both readings greater than the specified value? | 250 K ohms | Go to Diagnostic Aids | |||||||
13 |
Are both readings greater than the specified value? | 250 K ohms | ||||||||
14 | Replace the A/T Wiring Harness Assembly. Refer to TCC PWM Solenoid, TCC Solenoid, and Wiring Harness Replacement. Is the replacement complete? | -- | -- | |||||||
15 | Replace the 2-3 SS Valve. Refer to Control and Shift Solenoids Replacement. Is the replacement complete? | -- | -- | |||||||
16 | In order to verify your repair, perform the following procedure:
Has the test run and passed? | -- | System OK |
