Roof Panel Replacement SUT

Caution: Refer to Approved Equipment for Collision Repair Caution in the Preface section.

1. Disable the SIR system. Refer to SIR Disabling and Enabling in SIR.
2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.



3. Remove all related panels and components.
4. Repair as much of the damage as possible to factory specifications.

Caution: Refer to Foam Sound Deadeners Caution in the Preface section.

5. Note the location and remove the sealers and anti-corrosion materials from the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair in Paint and Coatings.




Important: Do not damage any inner panels or reinforcements.

6. Locate and drill out all factory welds. Note the number and location of the welds for installation of the roof panel.



7. Remove the damaged roof panel.

Important: If the location of the original plug weld holes can not be determined, or if structural weld-thru adhesive is present, space the plug weld holes every 40 mm (1½ in) apart.

1. Drill 8 mm (5/16 in) plug weld holes in the service part as necessary in the locations noted from the original panel.
2. Prepare all attachment surfaces as necessary.



3. Apply 3M® Weld-Thru coating P/N 05916 or equivalent to all mating surfaces
4. Position the roof panel.



5. Plug weld accordingly.



6. Clean and prepare all welded surfaces.
7. Apply the sealers and anti-corrosion materials to the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair in Paint and Coatings.
8. Paint the repair area. Refer to Basecoat/Clearcoat Paint Systems in Paint and Coatings.
9. Install all related panels and components.
10. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
11. Enable the SIR system. Refer to SIR Disabling and Enabling in SIR.

Roof Panel Replacement SUV

Caution: Refer to Approved Equipment for Collision Repair Caution in the Preface section.

1. Disable the SIR system. Refer to SIR Disabling and Enabling in SIR.
2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.



3. Remove all related panels and components.

Caution: Refer to Foam Sound Deadeners Caution in the Preface section.

4. Restore as much of the damage as possible to factory specifications.
5. Note the location and remove the sealers and anti-corrosion materials from the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair in Paint and Coatings.




Important: Do not damage any inner panels or reinforcements.

6. Locate and drill out all factory welds. Note the number and location of the welds for installation of the roof panel.



7. Remove the damaged roof panel.

Important: In any area damaged beyond recognition, or structural weld thru adhesive was present, space the plug weld holes 40 mm (1½ in) apart.

1. Drill 8 mm (5/16 in) plug weld holes in the service part as necessary in the locations noted from the original panel.
2. Prepare all attachment surfaces as necessary.



3. Apply 3m weld-thru coating P/N 05916 or equivalent to all mating surfaces.
4. Position the roof panel.



5. Plug weld accordingly.



6. Clean and prepare all welded surfaces.
7. Apply the sealers and anti-corrosion materials to the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair in Paint and Coatings.
8. Paint the repair area. Refer to Basecoat/Clearcoat Paint Systems in Paint and Coatings.
9. Install all related panels and components.
10. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
11. Enable the SIR system. Refer to SIR Disabling and Enabling in SIR.