GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 GMC_Truck 🢒 1998 🢒 GMC P42 Commercial Chassis 🢒 General Information 🢒 Maintenance and Lubrication 🢒 Maintenance Schedule - Long Trip/Highway

Maintenance Schedule - Long Trip/Highway Gasoline

Perform the services shown in this schedule up to 166 000 km (100,000 miles) and after 166 000 km (100,000 miles) at the same intervals.

12 500 Km (7,500 Miles)

    • Change the engine oil and the filter every 12 500 km (7,500 miles) or every 12 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following components. Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaking.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

25 000 Km (15,000 Miles)

    • Change the engine oil and the filter every 25 000 km (15,000 miles) or every 12 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following components. Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaking.
    • Inspect the shields and the underhood insulation (GVWR above 3,855 kg lbs).

37 500 Km (22,500 Miles)

    • Change the engine oil and the filter every 37 500 km (22,500 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following components. Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaking.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

50 000 Km (30,000 Miles)

    • Change the engine oil and the filter every 50 000 km (30,000 miles) or every 12 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following components. Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaking.
    • Clean and repack the front wheel bearings (or at each brake relining, whichever occurs first).
    • Replace the air filter.
    • Replace the fuel filter. An Emission Control Service *
    • Inspect the shields and the underhood insulation.

62 500 Km (37,500 Miles)

    • Change the engine oil and the filter every 62 500 km (37,500 miles ) or every 12 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following components. Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaking.

75 000 km (45,000 miles)

    • Change the engine oil and the filter every 75 000 km (45,000 miles) or every 12 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following components. Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaking.

83 000 Km (50,000 Miles)

    • Change the automatic transmission fluid and the filter. Refer to Automatic Transmission Fluid/Filter Changing in Automatic Transmission.
    • Manual transmission fluid doesn't require change.

87 500 Km (52,500 Miles)

    • Change the engine oil and filter every 87 500 km (52,500 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following components. Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaking.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

100 000 Km (60,000 Miles)

    • Change the engine oil and filter every 100 000 km  (60,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following components. Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaking.
    • Clean and repack the front wheel bearings (or at each brake relining, which ever occurs first).
    • Inspect the engine accessory drive belt. An Emission Control Service *
    • Replace the air filter.
    • Replace the fuel filter. An Emission Control Service *
    • Inspect the following components for damage or leaks. Replace the parts as needed. An Emission Control Service *
       - Fuel tank
       - Fuel cap
       - Fuel lines
       - Fuel cap gasket
    • If the engine has a thermostatically controlled cooling fan, inspect all of the hoses and all of the ducts for proper hook-up. Ensure that the valve works properly.
    • Conduct an Exhaust Gas Recirculation (EGR) system inspection.
    • Preform the following steps in order to conduct an evaporative control system inspection:
        1. Inspect all the fuel and vapor lines and hoses for proper hook-up, routing and condition.
        2. Ensure that the purge valve works properly (if equipped).
        3. Replace the vapor lines, hoses, and the purge valve as needed.

112 500 Km (67,500 Miles)

    • Change the engine oil and the filter (or every 3 months, whichever occurs first). An Emission Control Service *
    • Lubricate the following components. Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaking.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

125 000 Km (75,000 Miles)

    • Change the engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service *
    • Lubricate the following components. Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaking.

137 500 Km (82,500 Miles)

    • Change the engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service *
    • Lubricate the following components. Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaking.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

150 000 Km (90,000 Miles)

    • Change the engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service *
    • Lubricate the following components. Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaking.
    • Clean and repack the front wheel bearings (or at each brake relining, whichever occurs first).
    • Replace the air filter.
    • Replace the fuel filter. An Emission Control Service *

162 500 Km (97,500 Miles)

    • Change the engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service *
    • Lubricate the following components. Do not lubricate the ball joints unless the ball joint temperature is -12°C (10°F) or higher.
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaking.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

166 000 Km (100,000 Miles)

    • Inspect the spark plug wires.
    • Replace the spark plug wires. An Emission Control Service *
    • Change the automatic transmission fluid and the filter. Refer to Automatic Transmission Fluid/Filter Changing in Automatic Transmission.
    • Manual transmission fluid doesn't require change.
    • Inspect the positive crankcase ventilation (PCV) valve.

240 000 Km (150,000 Miles)

    • Drain, flush and refill the cooling system (or every 60 months since the last service, whichever comes first). Refer to Fluid and Lubricant Recommendations .
    • Inspect the hoses.
    • Clean the following components. An Emission Control Service *
       - The radiator
       - The condenser
       - The pressure cap
       - The neck

Maintenance Schedule - Long Trip/Highway Diesel

Perform the services shown in this schedule up to 240 000 km (150,000 miles) in this schedule and after 244 000 km (150,000 miles) at the same intervals.

8 000 Km (5,000 Miles)

    • Change the engine oil and the filter every 8 000 km (5,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate the ball joints unless their temperature is -12°C (10°F) or higher.
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

16 000 Km (10,000 Miles)

    • Change engine oil and filter every 16 000 km (10,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate the ball joints unless their temperature is -12°C (10°F) or higher.
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Inspect the air intake system installation in order to ensure that the gaskets are properly sealed.
    • Inspect the air intake system installation in order to ensure that hose connections, fasteners and other components are tightly fitted.
    • Inspect the air cleaning housing in order to ensure that the air cleaning housing is properly seated, the cover and wing nuts are tightly fitted.
    • Inspect the air cleaning housing in order to ensure that the air cleaning housing cover and wing nuts are tightly fitted.
    • Tighten the connections and fasteners. Replace the necessary damaged components.
    • Inspect the hoses and ducts for the proper maintenance if the engine has a thermostatically controlled cooling fan. Verify that the valves operate properly.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

24 000 Km (15,000 Miles)

    • Change engine oil and filter at 24 000 km (15,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate ball joints unless the ball joint temperature exceeds -12°C (10°F) or higher.
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

32 000 Km (20,000 Miles)

    • Change engine oil and filter every 32 000 km (20,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate ball joints unless the ball joint temperature exceeds -12°C (10°F) or higher.
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Inspect the air intake system installation in order to ensure that the gaskets are properly sealed.
    • Inspect the air intake system installation in order to ensure that hose connections, fasteners and other components are tightly fitted.
    • Inspect the air cleaning housing in order to ensure that the air cleaning housing is properly seated, the cover and wing nuts are tightly fitted.
    • Inspect the air cleaning housing in order to ensure that the air cleaning housing cover and wing nuts are tightly fitted.
    • Tighten the connections and fasteners. Replace the necessary damaged components.
    • Inspect the hoses and ducts for the proper maintenance if the engine has a thermostatically controlled cooling fan. Verify that the valves operate properly.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

40 000 Km (25,000 Miles)

    • Change engine oil and filter every 40 000 km (25,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate ball joints unless the ball joint temperature exceeds -12°C (10°F) or higher.
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

48 000 Km (30,000 Miles)

    • Change engine oil and filter every 48 000 km (30,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate ball joints unless the ball joint temperature exceeds -12°C (10°F) or higher.
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Replace the air filters. An Emission Control Service *
    • Clean the front wheel bearings or each brake relining, whichever occurs first.
    • Repack the front wheel bearings or each brake relining, whichever occurs first.
    • Replace the oil filter.
    • Inspect the shields and underhood insulation for looseness. Adjust or replace the shields and underhood insulation as required.
    • Inspect the air intake system installation in order to ensure that the gaskets are properly sealed.
    • Inspect the air intake system installation in order to ensure that hose connections, fasteners and other components are tightly fitted.
    • Inspect the air cleaning housing in order to ensure that the air cleaning housing is properly seated, the cover and wing nuts are tightly fitted.
    • Tighten the connections and fasteners. Replace the necessary damaged components.
    • Inspect the hoses and ducts for the proper maintenance if the engine has a thermostatically controlled cooling fan. Verify that the valves operate properly.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

56 000 Km (35,000 Miles)

    • Change engine oil and filter every 56 000 km (35,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate ball joints unless the ball joint temperature exceeds -12°C (10°F) or higher.
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

64 000 Km (40,000 Miles)

    • Change engine oil and filter every 64 000 km (40,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate ball joints unless the ball joint temperature exceeds -12°C (10°F) or higher.
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Inspect the air intake system installation in order to ensure that hose connections, fasteners and other components tightly fitted.
    • Inspect the air cleaning housing in order to ensure that the air cleaning housing is properly seated, the cover and wing nuts are tightly fitted.
    • Tighten the connections and fasteners. Replace the necessary damaged components.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

72 000 Km (45,000 Miles)

    • Change engine oil and filter every 72 000 km (45,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate ball joints unless the ball joint temperature exceeds -12°C (10°F) or higher.
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

80 000 Km (50,000 Miles)

    • Change engine oil and filter every 80 000 km (50,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate ball joints unless the ball joint temperature exceeds -12°C (10°F).
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Change the automatic transmission fluid and filter. Refer to Automatic Transmission Fluid/Filter Changing in Automatic Transmission.
    • Manual transmission fluid doesn't require change.
    • Inspect the air intake system installation in order to ensure that the gaskets are properly sealed.
    • Inspect the air intake system installation in order to ensure that hose connections, fasteners and other components tightly fitted.
    • Inspect the air cleaning housing in order to ensure that the air cleaning housing is properly seated, the cover and wing nuts are tightly fitted.
    • Tighten the connections and fasteners. Replace the necessary damaged components.
    • Inspect the hoses and ducts for the proper maintenance if the engine has a thermostatically controlled cooling fan. Verify that the valves operate properly.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

88 000 Km (55,000 Miles) 

    • Change engine oil and filter every 88 000 km (55,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate ball joints unless the ball joint temperature exceeds -12°C (10°F) or higher.
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.

96 000 Km (60,000 Miles)

    • Change engine oil and filter every 96 000 km (60,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate ball joints unless the ball joint temperature exceeds -12°C (10°F) or higher.
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Replace the air filter. An Emission Control Service. *
    • Clean the front wheel bearings or each brake relining, or whichever occurs first.
    • Repack the front wheel bearing or each brake relining, or whichever occurs first.
    • Inspect the crankcase depression regulator valve system for the following faulty conditions. This is also an Emission Control Service. *
       - Worn hoses
       - Plugged hoses
       - Collapsed hoses
    • Replace the fuel filter.
    • Inspect the equipped EGR System except for Code F engine. An Emission Control Service.
    • Inspect the shields and the underhood insulation for looseness. Adjust or replace the shields and the underhood insulation if damaged or loosed.
    • Change the automatic transmission fluid and filter if the vehicle's GVWR exceeds 3900 kg (8,600 lbs).
    • Change the automatic transmission fluid and filter if the vehicle is mainly driven under one or more of the following conditions.
       - In heavy traffic with outdoor temperatures exceeding 32° C (90° F) or higher.
       - In hilly and mountainous terrain
       - For frequent trailer towing
       - Uses found in the following services
   - Taxi
   - Police
   - Delivery
    • Inspect the air intake system installation in order to ensure that the gaskets are properly sealed.
    • Inspect the air intake system installation in order to ensure that hose connections, fasteners and other components tightly fitted.
    • Inspect the air cleaning housing in order to ensure that the air cleaning housing is properly seated, the cover and wing nuts are tightly fitted.
    • Tighten the connections and fasteners. Replace the necessary damaged components.
    • Inspect the hoses and ducts for the proper maintenance if the engine has a thermostatically controlled cooling fan. Verify that the valves operate properly.
    • Inspect the air intake system installation in order to ensure that the gaskets are properly sealed.
    • Inspect the air intake system installation in order to ensure that hose connections, fasteners and other components tightly fitted.
    • Inspect the air cleaning housing in order to ensure that the air cleaning housing is properly seated, the cover and wing nuts are tightly fitted.
    • Tighten the connections and fasteners. Replace the necessary damaged components.
    • Inspect the hoses and ducts for the proper maintenance if the engine has a thermostatically controlled cooling fan. Verify that the valves operate properly.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

104 000 Km (65,000 Miles)

    • Change engine oil and filter every 104 000 km (65,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate ball joints unless the ball joint temperature exceeds -12°C (10°F) or higher.
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

112 000 Km (70,000 Miles)

    • Change engine oil and filter every 112 000 km (70,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate ball joints unless the ball joint temperature exceeds -12°C (10°F) or higher.
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Inspect the air intake system installation in order to ensure that the gaskets are properly sealed.
    • Inspect the air intake system installation in order to ensure that hose connections, fasteners and other components tightly fitted.
    • Inspect the hoses and ducts for the proper maintenance if the engine has a thermostatically controlled cooling fan. Verify that the valve operate properly.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

120 000 Km (75,000 Miles)

    • Change engine oil and filter every 120 000 km (75,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate ball joints unless the ball joint temperature exceeds -12°C (10°F) or higher.
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

128 000 Km (80,000 Miles)

    • Change engine oil and filter every 128 000 km (80,000 miles) or every 3 months, or whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate ball joints unless the ball joint temperature exceeds -12°C (10°F) or higher.
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Inspect the air intake system installation in order to ensure that the gaskets are properly sealed.
    • Inspect the air intake system installation in order to ensure that hose connections, fasteners and other components tightly fitted.
    • Inspect the hoses and ducts for the proper maintenance if the engine has a thermostatically controlled cooling fan. Verify that the valves operate properly.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

136 000 Km (85,000 Miles)

    • Change engine oil and filter every 136 000 km (85,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate ball joints unless the ball joint temperature exceeds -12°C (10°F).
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

144 000 Km (90,000 Miles)

    • Change engine oil and filter every 144,000 km (90,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate ball joints unless the ball joint temperature exceeds -12°C (10°F) or higher.
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Replace the air filter. An Emission Control Service.
    • Clean the front wheel bearings or each brake relining, or whichever occurs first.
    • Repack the front wheel bearing or each brake relining, or whichever occurs first.
    • Replace the fuel filter.
    • Inspect the shields and underhood insulation for looseness. Adjust the shields and underhood insulation as required.
    • Inspect the air intake system installation in order to ensure that the gaskets are properly sealed.
    • Inspect the air intake system installation in order to ensure that hose connections, fasteners and other components tightly fitted.
    • Inspect the hoses and ducts for the proper maintenance if the engine has a thermostatically controlled cooling fan. Verify that the valves operate properly.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

152 000 Km (95,000 Miles)

    • Change engine oil and filter every 152 000 km (95,000 miles) or every 3 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate ball joints unless the ball joint temperature exceeds -12°C (10°F) or higher.
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

160 000 Km (100,000 Miles)

    • Change engine oil and filter every 160 000 km (100,000 miles) or every 60 months, whichever occurs first. An Emission Control Service *
    • Lubricate the following vehicle components when performing a maintenance schedule:
       - The front suspension
       - The steering linkage
       - The transmission shift linkage
       - The parking brake cable guides
       - The rear driveline center splines
       - The brake pedal springs
    • Do not lubricate ball joints unless the ball joint temperature exceeds -12°C (10°F) or higher.
    • Inspect the rear axle fluid level. Add fluid as needed.
    • Inspect the axle seals for leaks.
    • Inspect the radiator and heater hoses, if the hoses are cracked, swollen, or deteriorated, replace them. Tighten the hose clamps except for the constant tension clamps. Remove and clean the debris out the radiator and the air conditioning condenser.
    • Change the automatic transmission fluid and filter. Refer to Automatic Transmission Fluid/Filter Changing in Automatic Transmission.
    • Manual transmission fluid doesn't require change.
    • Inspect the shields and underhood insulation for looseness. Adjust the shields and underhood insulation as required.
    • Inspect the air intake system installation in order to ensure that the gaskets are properly sealed.
    • Inspect the air intake system installation in order to ensure that hose connections, fasteners and other components tightly fitted.
    • Inspect hoses and ducts for the proper maintenance if the engine has a thermostatically controlled cooling fan. Ensure that the valve operates properly.
    • Rotate the tires. Refer to Tire Rotation in Tires and Wheels.

240 000 Km (150,000 Miles)

    • Drain, flush and refill the cooling system every 240 000 km (150,000 miles ) or every 60 months, whatever exceeds first. Refer to Recommended Fluid and Lubricants.
    • Inspect the hoses.
    • Clean the radiator, condenser, pressure cap and neck. Pressure test the radiator and the cap. An Emission Control Service *