GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Daewoo 🢒 2009 🢒 Lacetti (Global Delta) 🢒 Body Repair 🢒 Collision Repair 🢒 Body Side Inner Panel Sectioning

Removal Procedure

    Warning: Refer to Approved Equipment for Collision Repair Warning in the Preface section.

    Warning: Refer to Collision Sectioning Warning in the Preface section.

    Warning: Refer to Glass and Sheet Metal Handling Warning in the Preface section.

  1. Disable the SIR System. Refer to SIR Disabling and Enabling.
  2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  3. Remove all related panels and components.
  4. Visually inspect the damage. Repair as much of the damage as possible.
  5. Remove the sealers and anti-corrosion materials from the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.

    6. Object Number: 2028146 Size: SH
  6. Create cut lines on the body lock pillar upper reinforcement (1).

    7. Object Number: 2028145 Size: SH

    Note: Do not damage any other panels or reinforcements.

  7. Cut the panel where sectioning is to be performed.

    8. Object Number: 2028147 Size: SH
  8. Locate and mark all the necessary factory welds of the body lock pillar upper reinforcement.
  9. Drill all factory welds. Note the number and location of welds for installation of the service assembly.

    10. Object Number: 2028148 Size: SH
  10. Remove the damaged body lock pillar upper reinforcement.

    11. Object Number: 2028149 Size: SH
  11. Create cut lines on the body side inner panel.

    12. Object Number: 2028150 Size: SH

    Note: Do not damage any other panels or reinforcements.

  12. Cut the panel where sectioning is to be performed.

    13. Object Number: 2028151 Size: SH

    Note: Drill hidden factory welds where body side outer rear panel drain gutter (1) and body side inner panel overlap.

  13. Locate and mark all the necessary factory welds of the body side inner panel.
  14. Drill all factory welds. Note the number and location of welds for installation of the service assembly.

    15. Object Number: 2028152 Size: SH
  15. Remove the damaged body side inner panel.

Installation Procedure

    Object Number: 2028153 Size: SH
  1. Remove rear end upper panel extension (1) from service part.

    2. Object Number: 2028154 Size: SH
  2. Cut the body side inner panel in corresponding locations to fit the remaining original panel. The sectioning joint should be trimmed to allow a gap of one-and-one-half-times the metal thickness at the sectioning joint.
  3. Create a 50 mm (2 in) backing plate from the unused portion of the service part.
  4. Drill 8 mm (5/16 in) along the sectioning cut on the remaining original part. Locate these holes 13 mm (1/2 in) from the edge of part and spaced 40 mm (1 1/2 in) apart.
  5. Prepare all mating surfaces as necessary.
  6. Fit the backing plates halfway into the sectioning joints, clamp in place and plug weld to the vehicle.
  7. Align the body side inner panel.

    8. Object Number: 2028155 Size: SH
  8. Drill 8 mm (5/1 in) for plug welding along the edges of the body side inner panel as noted from the original panel.
  9. Clean and prepare the attaching surfaces for welding.

    10. Object Number: 2028152 Size: SH
  10. Position the body side inner panel.
  11. Verify the fit of the panel.
  12. Clamp the body side inner panel into position.

    13. Object Number: 2028156 Size: SH
  13. Plug weld accordingly.
  14. To create a solid weld with minimum heat distortion, make 25 mm (1 in) stitch welds along the seam with 25 mm (1 in) gaps between them. Then go back and complete the stitch weld.

    15. Object Number: 2028157 Size: SH
  15. Cut the body lock pillar upper reinforcement in corresponding locations to fit the remaining original panel. The sectioning joint should be trimmed to allow a gap of one-and-one-half-times the metal thickness at the sectioning joint.
  16. Create a 50 mm (2 in) backing plate from the unused portion of the service part.
  17. Drill 8 mm (5/16 in) along the sectioning cut on the remaining original part. Locate these holes 13 mm (1/2 in) from the edge of part and spaced 40 mm (1 1/2 in) apart.
  18. Prepare all mating surfaces as necessary.
  19. Fit the backing plates halfway into the sectioning joints, clamp in place and plug weld to the vehicle.
  20. Align the body lock pillar upper reinforcement.

    21. Object Number: 2028158 Size: SH
  21. Drill 8 mm (5/1 in) for plug welding along the edges of the body lock pillar upper reinforcement as noted from the original panel.
  22. Clean and prepare the attaching surfaces for welding.

    23. Object Number: 2028148 Size: SH
  23. Position the body lock pillar upper reinforcement.
  24. Verify the fit of the panel.
  25. Clamp the body lock pillar upper reinforcement into position.

    26. Object Number: 2028159 Size: SH
  26. Plug weld accordingly.
  27. Apply the sealers and anti-corrosion materials to the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.
  28. Paint the repaired area. Refer to Basecoat/Clearcoat Paint Systems.
  29. Install all related panels and components.
  30. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  31. Enable the SIR system. Refer to SIR Disabling and Enabling.