DTC P0133, P1133, or P1134. Chevrolet Vivant 2007

For 1990-2009 cars only

Makes 🢒 Chevrolet 🢒 2007 🢒 Vivant 🢒 DTC 🢒 DTC P0133, P1133, or P1134

Diagnostic Instructions

•	Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

•	Review Strategy Based Diagnosis for an overview of the diagnostic approach.

•	Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC P0133: HO2S Slow Response Sensor 1

DTC P1133: HO2S Insufficient switching Sensor 1

DTC P1134: HO2S transition time ratio Sensor 1

Diagnostic Fault Information

Circuit	Short to Ground	Open/High Resistance	Short to Voltage	Signal Performance
HO2S Signal	P0131, P0137	P0134, P0140	P0132, P0138	P0133
Low Reference	--	P0134, P0140	P0132, P0138	P0133

The heated oxygen sensors (HO2S) are used for fuel control and catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content of the exhaust stream. When the engine is started, the control module operates in an Open Loop mode, ignoring the HO2S signal voltage while calculating the air-to-fuel ratio. The control module supplies the HO2S with a reference, or bias voltage of about 450 mV. While the engine runs, the HO2S heats up and begins to generate a voltage within a range of 0-1,000 mV. This voltage will fluctuate above and below the bias voltage. Once sufficient HO2S voltage fluctuation is observed by the control module, Closed Loop is entered. The control module uses the HO2S voltage to determine the air-to-fuel ratio. An HO2S voltage that increases above bias voltage toward 1,000 mV indicates a rich fuel mixture. An HO2S voltage that decreases below bias voltage toward 0 mV indicates a lean fuel mixture.

The heating elements inside each HO2S heat the sensor to bring the sensor up to operating conditions faster. This allows the system to enter Closed Loop earlier and the control module to calculate the air-to-fuel ratio sooner.

The HO2S utilizes the following circuits:

•	A signal circuit

•	A low reference circuit

•	An ignition 1 voltage circuit

•	A heater control circuit

Conditions for Running the DTC

•	DTCs P0106, P0107, P0108, P0117, P0118, P0122, P0123, P0131, P0132, P0134, P0171, P0172, P0201, P0202, P0203, P0204, P0300, P0336, P0337, P0351, P0352, P0401, P0402, P0404, P0405, P0406, P0443, P0502, P0506, P0507, P1166 and P1404 are not set.

•	The calculated airflow into the engine is between 9-40 g/s.

•	The engine speed is between 1,600-4,300 RPM.

•	The engine coolant temperature is greater than 70°C (158°F).

•	The ignition 1 voltage is greater than 10 volts.

•	The fuel system is in closed loop.

•	The engine has been operating for 60 seconds.

•	The EVAP purge is less than 20 percent.

•	The DTC runs continuously when the above conditions are met for 2 seconds.

Schematic Reference

Engine Controls Schematics

Connector End View Reference

•	Engine Control Module Connector End Views

•	Engine Controls Connector End Views

Electrical Information Reference

•	Circuit Testing

•	Connector Repairs

•	Testing for Intermittent Conditions and Poor Connections

•	Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

•	Scan Tool Data List

•	Scan Tool Data Definitions

•	Scan Tool Output Controls

Circuit/System Verification

Verify that other DTCs are not set.

⇒	If any DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle .

Operate the vehicle within the conditions for running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records. DTCs P0133, P1133, and P1134 should not set.

Circuit/System Testing

Verify that none of the following conditions exist:

•	Lean or rich fuel injectors--Refer to Fuel Injector Balance Test with Special Tool .

•	Water intrusion in the HO2S harness connector.

•	HO2S wiring harness damage

•	Incorrect RTV sealant

•	Low or high fuel system pressure--Refer to Fuel System Diagnosis .

•	Fuel that is contaminated--Refer to Alcohol/Contaminants-in-Fuel Diagnosis .

•	Fuel saturation of the evaporative emission (EVAP) canister.

•	Exhaust leaks near the HO2S.

•	Engine vacuum leaks.

•	Engine oil consumption .

•	Engine coolant consumption- Loss of Coolant .

⇒	If you find any of the above conditions, repair as necessary.

If all conditions test normal, replace the HO2S 1.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Control Module References for engine control module replacement, setup, and programming.