GM Service Manual Online
For 1990-2009 cars only

Object Number: 155201  Size: SF
ABS Components
Antilock Brake System Schematics
Handling ESD Sensitive Parts Notice

Circuit Description

The rotational movement of the toothed ring past the wheel speed sensor causes a change in the electromagnetic field which produces an AC voltage signal by the wheel speed sensor. The frequency of the sinusoidal (AC) voltage signal is proportional to the wheel speed. The amplitude of the AC voltage signal is directly related to wheel speed and the proximity of the wheel speed sensor to the toothed ring. The proximity of the wheel speed sensor to the toothed ring is also referred to as the air gap.

Conditions for Setting the DTC

DTC C1226 can set when the brake is off.

DTC C1226 detects a situation in which the right front wheel acceleration or deceleration is beyond specified limits.

Action Taken When the DTC Sets

    • A malfunction DTC stores.
    • The ABS/TCS disables.
    • The amber ABS/TCS warning indicators turn on.

Conditions for Clearing the DTC

    • The condition responsible for setting the DTC no longer exists and the Scan Tool Clear DTC function is used.
    • 100 drive cycles pass with no DTC detected.

Diagnostic Aids

The following conditions may cause an intermittent malfunction:

    • A poor connection
    • Rubbed-through wire insulation
    • A broken wire inside the insulation

Use the enhanced diagnostic function of the Scan Tool in order to measure the frequency of the malfunction. Refer to the Scan Tool manual or Scan Tool Diagnostics located in this section for the procedure.

If the customer's comments reflect that the amber ABS warning indicator is on only during moist environmental changes (rain, snow, vehicle wash), inspect all of the wheel speed sensor circuitry for signs of water intrusion. If the DTC is not current, clear all DTCs and simulate the effects of water intrusion by using the following procedure:

  1. Add two teaspoons of salt to twelve ounces of water to make a five percent saltwater solution.
  2. Spray the suspected area with the five percent saltwater solution.
  3. Test drive the vehicle over various road surfaces (bumps, turns, etc.) above 24 km/h (15 mph) for at least 30 seconds.
  4. If the DTC returns, inspect the suspected circuits.

Thoroughly inspect any circuitry that may be causing the intermittent complaint for the following conditions:

    • Backed out terminals
    • Improper mating
    • Broken locks
    • Improperly formed or damaged terminals
    • Poor terminal-to-wiring connections
    • Physical damage to the wiring harness
    • Corrosion and/or water intrusion of terminals.

Important: Difficulty may occur when trying to locate the intermittent malfunctions in the wheel speed sensor. Do not disturb any of the electrical connections. Change electrical connections only when instructed to do so by a step in the diagnostic table. Changing the electrical connections at the correct time will ensure that an intermittent electrical connection will not be corrected until the source of the malfunction is found.

Front Wheel Speed Sensor Resistance

Resistance of the wheel speed sensor will increase with an increase in sensor temperature.

The following table contains resistance values for the front wheel speed sensors at varying temperatures for use in diagnosis. The values are approximate and should be used as a guideline for diagnosis.

Important: Zero the J 39200 test leads before making any resistance measurements.

Temperature (°C)

Temperature (°F)

Resistance (Ohms)

-34 to 4

-30 to 40

804 to 1066

5 to 43

41 to 110

956 to 1240

44 to 93

111 to 200

112 to 1463

Step

Action

Value(s)

Yes

No

1

Was the Diagnostic System Check performed?

--

Go to Step 2

Go to Diagnostic System Check

2

  1. Turn the ignition switch to the OFF position.
  2. Inspect the right front wheel speed sensor and the right front wheel speed sensor harness connector for physical damage.

Is there any physical damage?

--

Go to Step 23

Go to Step 3

3

Inspect the following components for physical damage:

    • The right front wheel speed sensor jumper harness
    • The right front wheel speed sensor jumper harness connectors

Is there any physical damage?

--

Go to Step 22

Go to Step 4

4

  1. Disconnect the right front wheel speed sensor directly at the right front wheel speed sensor connector.
  2. Use the J 39200 in order to measure the resistance between the right front wheel speed sensor connector terminal A and the right front wheel speed sensor connector terminal B.

Is the resistance within the specified range?

1020-1137 ohms at 20°C (68°F)

Go to Step 5

Go to Step 23

5

  1. Select the A/C VOLTAGE scale on the J 39200 .
  2. Spin the right front wheel by hand while observing the voltage reading on the J 39200 .

Is the voltage equal to or greater than the specified voltage?

100 mV

Go to Step 6

Go to Step 23

6

  1. Disconnect the 24-way EBCM/EBTCM connector C1.
  2. Use the J 39200 in order to measure the resistance between the 24-way EBCM/EBTCM connector C1 terminal A4 and the 24-way EBCM/EBTCM connector C1 terminal B3.

Is continuity present between the 24-way EBCM/EBTCM connector C1 terminal A4 and the 24-way EBCM/EBTCM connector C1 terminal B3?

--

Go to Step 8

Go to Step 7

7

  1. Inspect the 24-way EBCM/EBTCM connector C1 for the following conditions:
  2. • Damage
    • Poor terminal contact
    • Terminal corrosion
    • Damage, poor terminal contact, and terminal corrosion may cause a short between the 24-way EBCM/EBTCM connector C1 terminal A4 and the EBCM/EBTCM connector C1 terminal B3.
  3. Inspect the remaining terminals of the 24-way EBCM/EBTCM connector C1 for the following conditions:
  4. • Damage
    • Poor terminal contact
    • Terminal corrosion

Are there signs of poor terminal contact, corrosion, or damaged terminals?

--

Go to Step 21

Go to Step 9

8

Repair the short between CKT 872 and CKT 833.

Is the repair complete?

--

Go to Diagnostic System Check

--

9

Use the J 39200 in order to measure the resistance between the 24-way EBCM/EBTCM connector C1 terminal A4 and ground.

Is continuity present between the 24-way EBCM/EBTCM connector C1 terminal A4 and ground?

--

Go to Step 10

Go to Step 11

10

Repair the short to ground in CKT  872.

Is the repair complete?

--

Go to Diagnostic System Check

--

11

Use the J 39200 in order to measure the resistance between the 24-way EBCM/EBTCM connector C1 terminal B3 and ground.

Is continuity present between the 24-way EBCM/EBTCM connector C1 terminal B3 and ground?

--

Go to Step 12

Go to Step 13

12

Repair the short to ground in CKT  833.

Is the repair complete?

--

Go to Diagnostic System Check

--

13

Use the J 39200 in order to measure the resistance between the 24-way EBCM/EBTCM connector C1 terminal A4 and the wheel speed sensor connector terminal B.

Is continuity present in CKT 872 between the 24-way EBCM/EBTCM connector C1 terminal A4 and the wheel speed sensor connector terminal B?

--

Go to Step 15

Go to Step 14

14

Repair the open or high resistance in CKT  872.

Is the repair complete?

--

Go to Diagnostic System Check

--

15

Use the J 39200 in order to measure the resistance between the 24-way EBCM/EBTCM connector C1 terminal B3 and the wheel speed sensor connector terminal A.

Is continuity present in CKT 833 between the 24-way EBCM/EBTCM connector C1 terminal B3 and the wheel speed sensor connector terminal A?

--

Go to Step 17

Go to Step 16

16

Repair the open or high resistance in CKT  833.

Is the repair complete?

--

Go to Diagnostic System Check

--

17

  1. Reconnect the 24-way EBCM/EBTCM harness connector C1.
  2. Reconnect the right front wheel speed sensor harness connector.
  3. Install a Scan Tool .
  4. Test drive the vehicle at a speed above 24 km/h (15 mph) for at least 30 seconds.
  5. Use the Scan Tool in order to read the DTCs.

Does DTC C1222 set as a current DTC?

--

Go to Step 18

Go to Step 20

18

  1. Select Data List on the Scan Tool .
  2. Monitor the wheel speed sensor speeds.
  3. Use the following procedure when driving the vehicle in order to test the wheel speed sensor:
  4.  - Slowly accelerate to 65 km/h (40 mph).
     - Slowly decelerate to 0 km/h (0 mph).

Is the speed of the right front wheel speed sensor constantly higher than the speed of the three remaining wheel speed sensors?

--

Go to Step 23

Go to Step 19

19

Replace the EBCM/EBTCM. Refer to Electronic Brake and Traction Control Module Replacement .

Is the repair complete?

--

Go to Diagnostic System Check

--

20

Is the malfunction intermittent or not present at this time?

--

Go to Diagnostic Aids

Go to Diagnostic System Check

21

Replace all of the terminals that exhibit signs of poor terminal contact, corrosion, or damaged terminals.

Is the repair complete?

--

Go to Diagnostic System Check

--

22

Replace the right front wheel speed sensor jumper harness. Refer to Wheel Speed Sensor Jumper Harness Replacement .

Is the repair complete?

--

Go to Diagnostic System Check

--

23

Replace the right front wheel speed sensor. Refer to Wheel Speed Sensor Replacement .

Is the repair complete?

--

Go to Diagnostic System Check

--