The engine control module (ECM) uses information from the crankshaft position (CKP) sensor in order to determine when an engine misfire is occurring, and uses information from the camshaft position (CMP) sensor in order to determine which cylinder is misfiring. By monitoring variations in the crankshaft rotation speed for each cylinder, the ECM is able to detect individual misfire events. If the ECM detects a misfire rate sufficient to cause the emission levels to exceed mandated standards, DTC P0300 sets. Under certain driving conditions, a misfire rate can be high enough to cause the 3-way catalytic converter (TWC) to overheat, possibly damaging the converter. The malfunction indicator lamp (MIL) will flash ON and OFF when converter overheating, damaging conditions are present and DTC P0300 is set.

The ECM is detecting a crankshaft rotation speed variation indicating a misfire sufficient to cause emission or catalytic converter damaging levels to exceed mandated standards.

Schematic Reference

Electrical Information Reference

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Special Tools Required

J 26792 Spark Tester

1. Verify that no other DTCs are set.

⇒	If a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle .

2. Engine idling, verify there is no abnormal engine noise.

⇒	If there is an abnormal engine noise, refer to Symptoms - Engine Mechanical .

3. Observe the Misfire Current Counters with a scan tool. The Misfire Current Counters should not be incrementing. Random misfires that are not steadily incrementing may be normal.
4. If the vehicle passes the Circuit/System Verification test, then operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that are captured in the Freeze Frame/Failure Records List.

1. Verify that the following conditions do not exist:

•	The fuel injector wire harness electrical connectors are connected to the improper fuel injectors. Refer to Engine Controls Schematics .

•	Engine vacuum leaks

•	Fuel pressure that is too low or too high--Refer to Fuel System Diagnosis .

•	Contaminated fuel--Refer to Alcohol/Contaminants-in-Fuel Diagnosis .

•	Restricted exhaust system--Refer to Restricted Exhaust .

2. Ignition OFF, remove the spark plug wire from the spark plug and ignition coil. Inspect and test the spark plug wire for arcing, cuts, rubbing on other components, and proper resistance. Refer to Spark Plug Wire Inspection and Ignition System Specifications .

⇒	If a fault is found, replace the spark plug wire. Refer to Spark Plug Wire Replacement .

3. Install the spark plug wire to the ignition coil.
4. Install the J 26792 to the boot of the spark plug wire and ground.

Important: An erratic or weak spark is considered a no spark condition.

5. Attempt to start the engine and observe the J 26792 . The spark tester should spark.

⇒	If there is no spark, refer to Electronic Ignition (EI) System Diagnosis for diagnosis of the ignition coil.

6. Ignition OFF, remove the spark plug from the misfiring cylinder. Verify that the following conditions do not exist with the spark plug:

•	Gas, coolant, or oil fouled

•	Cracked, worn, incorrectly gapped--Refer to Spark Plug Inspection .

⇒	If there is a condition with the spark plug, replace the spark plug.

7. Exchange the spark plug with another cylinder that is operating correctly.
8. Operate the engine under the conditions in which the misfire occurred. This may include putting the engine under a load, turning on the A/C, seat heaters, and rear window defog. Observe the Misfire Current Counters with a scan tool. The misfire should not follow the spark plug exchange.

⇒	If the misfire follows the spark plug, replace the spark plug.

9. If all conditions test normal, test or inspect for the following:

•	A lean or rich fuel injector--Refer to Fuel Injector Diagnosis .

•	An engine mechanical condition--Refer to Symptoms - Engine Mechanical .

1. Install any components or connectors that have been removed or replaced during diagnosis.
2. Perform any adjustment, programming, or setup procedures that are required when a component or module is removed or replaced.
3. Clear the DTCs.
4. Turn OFF the ignition for 60 seconds.
5. If the repair was related to a DTC, duplicate the Conditions for running the DTC and use the Freeze Frame/Failure Records, if applicable, in order to verify the DTC does not reset. If the DTC resets or another DTC is present, refer to Diagnostic Trouble Code (DTC) List - Vehicle and perform the appropriate diagnostic procedure.
6. To verify that the performance of the catalytic converter has not been affected by the condition that set this DTC, perform the Repair Verification for DTC P0420 or P0430. Refer to DTC P0420 or P0430 .