GM Service Manual Online
For 1990-2009 cars only

DTC P0480, P0481, P0691, P0692, P0693, or P0694 LX9

Circuit Description

The powertrain control module (PCM) controls the low speed cooling fan operation by grounding the low speed fan relay control circuit with an internal solid state device called a driver. For high speed cooling fan operation, the PCM grounds the high speed and S/P relay control circuit at the same time the low speed control circuit is grounded. Battery positive voltage is supplied to the low speed, high speed and S/P fan relays. When the PCM is commanding a fan relay ON, the voltage of the control circuit should be low, near 0 volts. When the PCM is commanding a fan relay OFF, the voltage potential of the control circuit should be high, near battery voltage. If the fault detection circuit senses a voltage other than what is expected, the DTC will set. The vehicle has DTCs which include DTC Symptoms. For more information on DTC Symptoms, refer to DTC Symptom Description in Vehicle DTC Information.

If the PCM detects an improper voltage level on the low or high speed driver circuits, then code P0480, P0481, P0691, P0692, P0693, or P0694, will set and the effected driver will be disabled.

    • P0480 -- Cooling Fan Relay 1 Control Circuit
    •  P0481-- Cooling Fan Relays  2 and 3 Control Circuit
    •  P0691 -- Cooling Fan Relay 1 Control Circuit Low Voltage
    • P0692 -- Cooling Fan Relay 1 Control Circuit High Voltage
    •  P0693 -- Cooling Fan Relay 2 and 3 Control Circuit Low Voltage
    • P0694 -- Cooling Fan Relay 2 and 3 Control Circuit High Voltage

The P0694 condition is present for 1 second.

Conditions for Running the DTC

    •  The ignition voltage is between 9.0-18.0 volts.
    • The engine speed is more than 40 RPM.
    •  The PCM driver transitions from ON to OFF or from OFF to ON.

Action Taken When the DTC Sets

    • The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and failed.
    • The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.

Conditions for Clearing the MIL/DTC

    • The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
    • The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
    • Use the scan tool Clear DTC Information function.

Diagnostic Aids

    • If the condition is not present, refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
    • Review the Freeze/Failure Records vehicle mileage since the diagnostic test failed. This may help determine how often the condition that caused the DTC to be set occurs.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. Listen for an audible click when the cool fan relay 1 operates. Command both the ON and OFF states. Repeat the commands as necessary.

  2. Listen for an audible click when the S/P and cool fan 2 relays operate. Command both the ON and OFF states. Repeat the commands as necessary.

Step

Action

Yes

No

Schematic Reference: Engine Cooling Schematics

Connector End View Reference: Cooling System Connector End Views

1

Did you perform the Diagnostic System Check-Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

  1. Install a scan tool.
  2. Turn the ignition ON, with the engine OFF.
  3. With a scan tool, command the Fan Control Relay 1 ON and OFF.

Does the cool fan 1 relay turn ON and OFF with each command?

Go to Step 3

Go to Step 4

3

With a scan tool, command the Fan Control Relay 2 and 3 ON and OFF.

Do the S/P and the cool fan 2 relays turn ON and OFF with each command?

Go to Diagnostic Aids

Go to Step 6

4

  1. Turn the ignition OFF.
  2. Disconnect the cool fan 1 relay.
  3. Turn the ignition ON, with the engine OFF.
  4. Probe the battery voltage circuit of the cool fan 1 relay with a test lamp that is connected to a good ground.

Does the test lamp illuminate?

Go to Step 5

Go to Step 16

5

  1. Connect a test lamp between the control circuit of the cool fan 1 relay and the battery voltage circuit of the cool fan 1 relay.
  2. With a scan tool, command the Fan Control Relay 1 ON and OFF.

Does the test lamp turn ON and OFF with each command?

Go to Step 12

Go to Step 9

6

  1. Turn the ignition OFF.
  2. Disconnect the cool fan 2 relay.
  3. Turn the ignition ON, with the engine OFF.
  4. Probe the battery voltage circuit of the cool fan 2 relay with a test lamp that is connected to a good ground.

Does the test lamp illuminate?

Go to Step 7

Go to Step 16

7

  1. Connect a test lamp between the control circuit of the cool fan 2 relay and the battery voltage circuit of the cool fan 2 relay.
  2. With a scan tool, command the Fan Control Relay 2 and 3 ON and OFF.

Does the test lamp turn ON and OFF with each command?

Go to Step 14

Go to Step 8

8

  1. Turn the ignition OFF.
  2. Disconnect the S/P fan relay.
  3. Turn the ignition ON, with the engine OFF.
  4. Connect a test lamp between the control circuit of the S/P fan relay and the battery voltage circuit of the S/P fan relay.
  5. With a scan tool, command the Fan Control Relay 2 and 3 ON and OFF.

Does the test lamp turn ON and OFF with each command?

Go to Step 13

Go to Step 9

9

Does the test lamp remain illuminated with each command?

Go to Step 11

Go to Step 10

10

Test the control circuit of the appropriate relay for a short to voltage or an open. Refer to Testing for Intermittent Conditions and Poor Connections and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 15

11

Test the control circuit of the appropriate relay for a short to ground. Refer to Testing for Intermittent Conditions and Poor Connections and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 15

12

Inspect for poor connections at the cool fan 1 relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 17

13

Inspect for poor connections at the S/P fan relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 18

14

Inspect for poor connections at the cool fan 2 relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 19

15

Inspect for poor connections at the harness connector of the powertrain control module (PCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 20

16

Repair the battery voltage circuit for an open or high resistance. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 21

--

17

Replace the cool fan 1 relay.

Did you complete the repair?

Go to Step 21

--

18

Replace the S/P fan relay.

Did you complete the repair?

Go to Step 21

--

19

Replace the cool fan 2 relay.

Did you complete the repair?

Go to Step 21

--

20

Important: Perform the programming procedure for the PCM.

Replace the PCM. Refer to Powertrain Control Module Replacement in Engine Controls - 3.5L.

Did you complete the replacement?

Go to Step 21

--

21

  1. Use the scan tool in order to clear the DTCs .
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

Go to Step 2

System OK

DTC P0480, P0481, P0691, P0692, P0693, or P0694 L61

Circuit Description

The powertrain control module (PCM) controls the low speed cooling fan operation by grounding the low speed fan relay control circuit with an internal solid state device called a driver. For high speed cooling fan operation, the PCM grounds the high speed and S/P relay control circuit at the same time the low speed control circuit is grounded. Battery positive voltage is supplied to the low speed, high speed and S/P fan relays. When the PCM is commanding a fan relay ON, the voltage of the control circuit should be low, near 0 volts. When the PCM is commanding a fan relay OFF, the voltage potential of the control circuit should be high, near battery voltage. If the fault detection circuit senses a voltage other than what is expected, the DTC will set. The vehicle has DTCs which include DTC Symptoms. For more information on DTC Symptoms, refer to DTC Symptom Description in Vehicle DTC Information.

If the PCM detects an improper voltage level on the low or high speed driver circuits, then code P0480, P0481, P0691, P0692, P0693, or P0694, will set and the effected driver will be disabled.

    • P0480 -- Cooling Fan Relay 1 Control Circuit
    •  P0481-- Cooling Fan Relays S/P and Relay 2 Control Circuit
    •  P0691 -- Cooling Fan Relay 1 Control Circuit Low Voltage
    • P0692 -- Cooling Fan Relay 1 Control Circuit High Voltage
    •  P0693 -- Cooling Fan Relay 2 Control Circuit Low Voltage
    • P0694 -- Cooling Fan Relays S/P and Relay 2 Control Circuit High Voltage

The P0694 condition is present for 1 second.

Conditions for Running the DTC

    •  The ignition voltage is between 9.0-18.0 volts.
    • The engine speed is more than 40 RPM.
    •  The PCM driver transitions from ON to OFF or from OFF to ON.

Action Taken When the DTC Sets

    • The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and failed.
    • The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.

Conditions for Clearing the MIL/DTC

    • The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
    • The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
    • Use the scan tool Clear DTC Information function.

Diagnostic Aids

    • If the condition is not present, refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
    • Review the Freeze/Failure Records vehicle mileage since the diagnostic test failed. This may help determine how often the condition that caused the DTC to be set occurs.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. Listen for an audible click when the cool fan relay 1 operates. Command both the ON and OFF states. Repeat the commands as necessary.

  2. Listen for an audible click when the S/P and cool fan 2 relays operate. Command both the ON and OFF states. Repeat the commands as necessary.

Step

Action

Yes

No

Schematic Reference: Engine Cooling Schematics

Connector End View Reference: Cooling System Connector End Views

1

Did you perform the Diagnostic System Check-Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

  1. Install a scan tool.
  2. Start the engine.
  3. With a scan tool, monitor the engine coolant (ECT) in the Inputs/Outputs scan tool data.
  4. Bring the vehicle up to normal operating temperature.
  5. At 106°C (223°F) the S/P and cool fan  2 relay should click on and the low speed engine cooling fans should engage.

Does the low speed cooling fans engage?

Go to Step 3

Go to Step 4

3

Important:: A 3 second delay occurs before the powertrain control module (PCM) changes the cooling fan speed.

  1. With a scan tool, monitor the engine coolant temperature (ECT) in the Inputs/Outputs scan tool data.
  2. At 110°C (230°F) the S/P and the cool fan 2 relays engage the high speed engine cooling fans.

Are the S/P and the cool fan 2 relays turned ON?

Go to Diagnostic Aids

Go to Step 6

4

  1. Turn the ignition OFF.
  2. Disconnect the cool fan 1 relay.
  3. Turn the ignition ON, with the engine OFF.
  4. Probe the battery voltage circuit of the cool fan 1 relay with a test lamp that is connected to a good ground.

Does the test lamp illuminate?

Go to Step 5

Go to Step 16

5

  1. Connect a test lamp between the control circuit of the cool fan 1 relay and the battery voltage circuit of the cool fan 1 relay.
  2. Ground the Low Speed Cooling Fan Relay Control Circuit to the PCM.

Does the test lamp illuminate?

Go to Step 12

Go to Step 9

6

  1. Turn the ignition OFF.
  2. Disconnect the cool fan 2 relay.
  3. Turn the ignition ON, with the engine OFF.
  4. Probe the battery voltage circuit of the cool fan 2 relay with a test lamp that is connected to a good ground.

Does the test lamp illuminate?

Go to Step 7

Go to Step 16

7

  1. Connect a test lamp between the control circuit of the cool fan 2 relay and the battery voltage circuit of the cool fan 2 relay.
  2. Ground the High Speed Cooling Fan Relay Control Circuit of the PCM.

Is the test lamp illuminated?

Go to Step 14

Go to Step 8

8

  1. Turn the ignition OFF.
  2. Disconnect the S/P fan relay.
  3. Turn the ignition ON, with the engine OFF.
  4. Connect a test lamp between the control circuit of the S/P fan relay and the battery voltage circuit of the S/P fan relay.
  5. Ground the High Speed Cooling Fan Relay Control Circuit to the PCM.

Does the test lamp illuminate?

Go to Step 13

Go to Step 9

9

Intermittently ground then remove the ground on the High Speed Cooling Fan Relay Control Circuit to the PCM.

Does the test lamp remain illuminated upon grounding the control circuit?

Go to Step 11

Go to Step 10

10

Test the control circuit of the appropriate relay for a short to voltage or an open. Refer to Testing for Intermittent Conditions and Poor Connections and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 15

11

Test the control circuit of the appropriate relay for a short to ground. Refer to Testing for Intermittent Conditions and Poor Connections and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 15

12

Inspect for poor connections at the cool fan 1 relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 17

13

Inspect for poor connections at the S/P fan relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 18

14

Inspect for poor connections at the cool fan 2 relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 19

15

Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 21

Go to Step 20

16

Repair the battery voltage circuit for an open or high resistance. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 21

--

17

Replace the cool fan 1 relay.

Did you complete the repair?

Go to Step 21

--

18

Replace the S/P fan relay.

Did you complete the repair?

Go to Step 21

--

19

Replace the cool fan 2 relay.

Did you complete the repair?

Go to Step 21

--

20

Important: Perform the programming procedure for the PCM.

Replace the PCM. Refer to Powertrain Control Module Replacement in Engine Controls - 2.2L.

Did you complete the replacement?

Go to Step 21

--

21

  1. Use the scan tool in order to clear the DTCs .
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

Go to Step 2

System OK