Circuit Description
The PCM controlled lamps are powered through the IGN 1 fuse. The PCM turns ON the bulb, LED, or driver info center indicator by supplying a path to ground through the PCM.
Diagnostic Aids
A PCM controlled lamp ON at all times most likely indicates that a condition is present which requires the attention of the vehicle operator. Conditions which will illuminate each lamp are as follows:
| • | GENERATOR LAMP will be illuminated under any of the following conditions: |
| - | When the engine speed is greater than 1200 RPM and system voltage falls below 10 volts for longer than 10 seconds. The PCM commands the generator lamp OFF when system voltage rises to above 12 volts. |
| - | When the generator control circuit (L terminal) remains low for longer than 10 seconds. |
| • | LOW OIL LEVEL LAMP When the ignition is first turned ON, the PCM commands the Low Oil Level lamp ON for a brief period of time (approximately 3 seconds) to test the bulb. If the engine oil level switch indicates that a low oil level condition exists, the PCM commands the Low Oil Level Lamp ON. The PCM will test for low oil level at key ON if either of the following conditions exist: |
| - | If the engine coolant temperature is below 15°C (59°F), the PCM checks the state of the engine oil level switch at startup. |
| - | If the engine coolant temperature is between 15°C (59°F) and 140°C (284°F),. the difference between engine coolant temperature at last key OFF and the engine coolant temperature at the current key ON is must be at least 12°C (54°F). |
For diagnosis of the instrument panel, perform the System Check in the Instrument Cluster section of Electrical Diagnosis.
Check for the following conditions:
| • | Poor connection at PCM. Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wire connection. |
| • | Damaged harness. Inspect the wiring harness for damage. If the harness appears to be OK, disconnect the PCM and turn the ignition ON. Observe a voltmeter connected to the affected PCM output circuit while moving connectors and wiring harnesses related to the PCM output circuit. A change in voltage will indicate the location of the fault. |
| • | Engine oil level switch circuit: If the problem was with the Low Oil Level lamp and PCM Controlled Warning Lamps did not isolate a problem, use Engine Oil Level Switch Diagnosis. |
Test Description
The number(s) below refer to the step number(s) on the Diagnostic Table:
-
Normally, ignition feed voltage should be present on the output driver circuit with the PCM disconnected and the ignition turned ON.
-
Checks for a shorted component or a short to B+ on the output driver circuit. Either condition would result in a measured current of over 1.5 amps. Also checks for a component that is going open while being operated, resulting in a measured current of 0 amps.
-
Checks for a faulty instrument cluster.
-
This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is being replaced, the new PCM must be programmed. Refer to PCM Replacement and Programming Procedures in Powertrain Control Module (PCM) and Sensors.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | Go to Powertrain OBD System Check | |
2 | Was the instrument cluster system check in Electrical Diagnosis performed? | -- | Go to Electrical Diagnosis | |
Is voltage near the specified value? | B+ | |||
Does the current reading remain between the specified values? | 0.05 Amp 1.5 Amps | |||
Is voltage at the specified value? | 0V | |||
6 | Locate and repair short to voltage in affected PCM output circuit. Is action complete? | -- | -- | |
7 | Check the ignition feed fuse for the instrument panel cluster indicator lamps. Is the fuse blown? | -- | ||
8 |
Is action complete? | -- | -- | |
9 |
Is voltage near the specified value? | B+ | ||
10 |
Was a problem found? | -- | ||
11 |
Was a problem found? | -- | ||
12 |
Does the test light flash ON and OFF? | -- | Refer to Diagnostic Aids | |
13 |
Was a problem found? | -- | ||
14 | Locate and repair open in ignition feed circuit to the instrument panel cluster indicator lamps (refer to Repair Procedures in Electrical Diagnosis Section 8A-5). Is action complete? | -- | -- | |
15 | Replace the instrument panel cluster. Is action complete? | -- | -- | |
Replace the PCM. Important: Replacement PCM must be programmed. Refer to PCM Replacement/Programming for procedures. Is action complete? | -- | -- | ||
17 | Operate the affected lamp using the scan tool output tests function. Does the affected lamp operate properly? | -- | System OK |
