GM Service Manual Online
For 1990-2009 cars only

Lack of Power, Sluggish or Spongy

Step

Action

Value(s)

Yes

No

DEFINITION: Engine delivers less than expected power Little or no increase in speed when accelerator pedal is pushed down part way.

1

Was the Powertrain On-Board Diagnostic (OBD) System Check performed?

Go to Step 2

Go to the Powertrain On Board Diagnostic (OBD) System Check

2

  1. Perform a bulletin search.
  2. If a bulletin that addresses the symptom is found, correct the condition as instructed in the bulletin.

Was a bulletin found that addresses the symptom?

Go to Step 16

Go to Step 3

3

Was visual/physical check performed?

Go to Step 4

Go to Visual/Physical Checks

4

  1. Remove and check air filter element for dirt, or for being restricted.
  2. Replace air filter element if necessary. Refer to Air Cleaner Element .

Was a repair required?

Go to Step 16

Go to Step 5

5

  1. Check for low fuel pressure. Refer to Fuel System Pressure Test .
  2. If a problem is found, repair as necessary.

Was a problem found?

Go to Step 16

Go to Step 6

6

  1. Check for contaminated fuel. Refer to Alcohol/Contaminants-in-Fuel Test .
  2. If a problem is found, repair as necessary.

Was a problem found?

Go to Step 16

Go to Step 7

7

  1. Using a scan tool, monitor KS system for excessive spark retard activity. Refer to Knock Sensor (KS) System .
  2. If a problem is found, repair as necessary.

Was a problem found?

Go to Step 16

Go to Step 8

8

  1. Check for proper ignition coil output voltage with spark tester J 26792 :
  2.  - Clip the spark tester to engine ground.
     - Connect one end of a spark plug wire to the spark tester; connect the other end of the spark plug wire to the coil being tested.
     - Connect one end of another spark plug wire to the other coil tower; connect the other end of the spark plug wire to ground.
     - Crank the engine while observing the spark tester; a crisp blue spark should be observed.
     - Repeat the above steps for each coil.
  3. If adequate spark is not present at all coils, repair as necessary.

Was a problem found?

Go to Step 16

Go to Step 9

9

  1. Remove spark plugs, check for wet plugs, cracks, wear, improper gap, burned electrodes, or heavy deposits.
  2. Notice: Determine the cause of the oil or gas fouled spark plugs in order to avoid damage to the new spark plugs.

  3. If a problem is found, repair as necessary.

Was a problem found?

Go to Step 16

Go to Step 10

10

  1. Check ignition coils for cracks or carbon tracking.
  2. If a problem is found, repair as necessary.

Was a problem found?

Go to Step 16

Go to Step 11

11

  1. Check PCM grounds for being clean, tight and in their proper locations. Refer to Engine Controls Schematics .
  2. If a problem is found, repair as necessary.

Was a problem found?

Go to Step 16

Go to Step 12

12

  1. Check exhaust system for possible restriction:
  2. • Inspect exhaust system for damaged or collapsed pipes.
    • Inspect muffler for heat distress or possible internal failure.
    • Check for a possible plugged Three-Way catalytic converter by checking exhaust system back pressure. Refer to Restricted Exhaust System Check
  3. If a problem is found, repair as necessary.

Was a problem found?

Go to Step 16

Go to Step 13

13

  1. Check Torque Converter Clutch (TCC) for proper operation Refer to 4T60-E Transaxle Diagnosis
  2. If a problem is found, repair as necessary.

Was a problem found?

Go to Step 16

Go to Step 14

14

  1. Engine mechanical problem Check for low compression, incorrect or worn camshaft, loose timing chain etc. Refer to Engine Mechanical.
  2. If a problem is found, repair as necessary.

Was a problem found?

Go to Step 16

Go to Step 15

15

  1. Review all diagnostic procedures within this table.
  2. When all procedures have been completed and no malfunctions are found, review/inspect the following:
  3. • Visual/physical inspection.
    • Scan Tool data.
    • Freeze Frame data/Failure Records Data.
    • All connections within a suspected circuit and/or system.
  4. If a problem is found, repair as necessary.

Was a problem found?

Go to Step 16

Refer to Technical Service Bulletins

16

Operate the vehicle to duplicate conditions present when the original symptom was noted.

Is symptom still present?

Go to Step 3

System OK