Inflatable Restraint Side Impact Sensor Replacement. Chevrolet Impala 2006

For 1990-2009 cars only

Makes 🢒 Chevrolet 🢒 2006 🢒 Impala 🢒 Restraints 🢒 SIR 🢒 Inflatable Restraint Side Impact Sensor Replacement

Inflatable Restraint Side Impact Sensor Replacement Impala

Callout	Component Name
Caution: Do not strike or jolt the inflatable restraint side impact sensor (SIS). Before applying power to the SIS make sure that it is securely fastened. Failure to observe the correct installation procedures could cause SIR deployment, personal injury, or unnecessary SIR system repairs. Caution: Refer to SIR Caution in the Preface section. Notice: Refer to Fastener Notice in the Preface section. Fastener Tightening Specifications: Refer to Fastener Tightening Specifications. Preliminary Procedure Disable the SIR system. Refer to SIR Disabling and Enabling for the left side or SIR Disabling and Enabling for the right. Remove the front door panel. Refer to Front Side Door Trim Panel Replacement.
1	Bolt/Screw, Inflatable Restraint Side Impact Sensor Assembly (Qty: 2) Tip Loosen the fasteners and slide the sensor out of the keyhole slots. Tighten 10 N·m (89 lb in)
2	Sensor Assembly, Inflatable Restraint Side Impact

Callout

Component Name

Caution: Do not strike or jolt the inflatable restraint side impact sensor (SIS). Before applying power to the SIS make sure that it is securely fastened. Failure to observe the correct installation procedures could cause SIR deployment, personal injury, or unnecessary SIR system repairs.

Caution: Refer to SIR Caution in the Preface section.

Notice: Refer to Fastener Notice in the Preface section.

Fastener Tightening Specifications: Refer to Fastener Tightening Specifications.

Preliminary Procedure

Disable the SIR system. Refer to SIR Disabling and Enabling for the left side or SIR Disabling and Enabling for the right.
Remove the front door panel. Refer to Front Side Door Trim Panel Replacement.

Bolt/Screw, Inflatable Restraint Side Impact Sensor Assembly (Qty: 2)

Tip
Loosen the fasteners and slide the sensor out of the keyhole slots.

Tighten
10 N·m (89 lb in)

Sensor Assembly, Inflatable Restraint Side Impact

Inflatable Restraint Side Impact Sensor Replacement Monte Carlo

Callout	Component Name
Caution: When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled. Refer to SIR Disabling and Enabling . Failure to observe the correct procedure could cause deployment of the SIR components, personal injury, or unnecessary SIR system repairs. Caution: Do not strike or jolt the inflatable restraint side impact sensor (SIS). Before applying power to the SIS make sure that it is securely fastened. Failure to observe the correct installation procedures could cause SIR deployment, personal injury, or unnecessary SIR system repairs. Notice: Refer to Fastener Notice in the Preface section. Fastener Tightening Specifications: Refer to Fastener Tightening Specifications . Preliminary Procedure Disable the SIR. Refer to SIR Disabling and Enabling or SIR Disabling and Enabling . Remove the side door trim panel. Refer to Front Side Door Trim Panel Replacement.
1	Inflatable Restraint Side Impact Sensor Assembly Bolt (Qty: 2) Tip Loosen the bolts and slide the sensor out of the key hole slots. Tighten 9 N·m (80 lb in)
2	Inflatable Restraint Side Impact Sensor Assembly

Callout

Component Name

Caution: When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled. Refer to SIR Disabling and Enabling . Failure to observe the correct procedure could cause deployment of the SIR components, personal injury, or unnecessary SIR system repairs.

Notice: Refer to Fastener Notice in the Preface section.

Fastener Tightening Specifications: Refer to Fastener Tightening Specifications .

Preliminary Procedure

Disable the SIR. Refer to SIR Disabling and Enabling or SIR Disabling and Enabling .
Remove the side door trim panel. Refer to Front Side Door Trim Panel Replacement.

Inflatable Restraint Side Impact Sensor Assembly Bolt (Qty: 2)

Tip
Loosen the bolts and slide the sensor out of the key hole slots.

Tighten
9 N·m (80 lb in)

Inflatable Restraint Side Impact Sensor Assembly