Circuit Description
The throttle body assembly contains 2 throttle position (TP) sensors. The TP sensors are mounted to the throttle body assembly and are not serviceable. The TP sensors provide a signal voltage that changes relative to throttle blade angle. The engine control module (ECM) supplies each TP sensor with a 5-volt reference circuit , a low reference circuit, and a signal circuit.
The TP sensors have opposite functionality . TP sensor 1 signal voltage decreases from above 4 volts at idle to below 1 volt at wide open throttle (WOT). TP sensor 2 signal voltage increases from below 1 volt at idle to above 4 volts at WOT.
If the ECM detects TP sensor 2 signal voltage is too high, this DTC will set.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0223 Throttle Position (TP) Sensor 2 Circuit High Voltage
Conditions for Running the DTC
| • | The ignition is ON, with the engine OFF, or the engine is operating. |
| • | The ignition 1 voltage is more than 5.23 volts. |
| • | DTC P0223 runs continuously when the above conditions are met. |
Conditions for Setting the DTC
The ECM detects the TP sensor 2 signal voltage is more than 4.73 volts for less than one second.
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame and/or the Failure Records. |
| • | The control module commands the TAC system to operate in the Reduced Engine Power mode. |
| • | A message center or an indicator displays Reduced Engine Power. |
| • | Under certain conditions the control module commands the engine OFF. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
| • | Use the J 35616 Connector Test Adapter Kit for any test that requires probing the ECM harness connector or a component harness connector. |
| • | If there is a condition with the TP sensors, the ECM defaults to reduced power mode for the entire ignition cycle, even if the condition is corrected. |
| • | For an intermittent condition, refer to Testing for Intermittent Conditions and Poor Connections . |
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Controls Connector End Views or Engine Control Module Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
2 |
Is the TP Sensor 2 Voltage parameter more than the specified value? | 4.73 V | Go to Step 4 | Go to Step 3 |
3 |
Did the DTC fail this ignition? | -- | Go to Step 4 | Go to Diagnostic Aids |
4 |
Does the DMM indicate voltage within the specified range? | 4.8-5.2 V | Go to Step 5 | Go to Step 10 |
5 | Probe the TP sensor signal circuit with a test lamp connected to ground. Does the test lamp illuminate? | -- | Go to Step 8 | Go to Step 6 |
6 | Observe the TP Sensor 2 parameter with a test lamp still connected to the TP sensor signal circuit. Does the scan tool indicate voltage at the specified value? | 0 V | Go to Step 9 | Go to Step 7 |
7 | Test the TP sensor 2 signal circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 13 |
8 | Test the signal 2 circuit of the TP sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 12 |
9 | Test the TP sensor 2 low reference circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 12 |
10 | Test the TP sensor 2 5-volt reference circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 11 |
11 | Test for shorted terminals and for a poor connection at the engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 15 |
12 | Test for an intermittent and for a poor connection at the throttle body harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 14 |
13 | Test for an intermittent and for a poor connection at the ECM harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 15 |
14 | Replace the throttle body assembly. Refer to Throttle Body Assembly Replacement . Did you complete the replacement? | -- | Go to Step 16 | -- |
15 | Replace the ECM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 16 | -- |
16 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 17 |
17 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | System OK | |
