GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2001 🢒 Impala 🢒 Body and Accessories 🢒 Body Front End 🢒 Windshield Washer Solvent Container Replacement

Removal Procedure
  1. Drain the washer solvent from the washer solvent container.

    2. Object Number: 334204 Size: SH
  2. Remove the screw from the upper tube assembly.
  3. Remove the upper tube assembly and the seal.

    4. Object Number: 334222 Size: SH
  4. Remove the right headlamp assembly. Refer to Headlamp Assembly or Headlamp Bulb and/or Cornering, Sidemarker, Park, Turn Signal Bulb Replacement in Lighting Systems.
  5. Remove the front washer solvent container screw.
  6. Remove the front fender liner. Refer to Front Fender Liner Replacement in Body Front End.
  7. Disconnect the electrical connector and the hose from the washer pump.
  8. Remove the washer solvent container screws.
  9. Pull the washer solvent container away from the vehicle.
  10. Disconnect the electrical connector from the washer solvent level sensor.
  11. Remove the washer solvent container.
  12. Remove the washer solvent container bracket screws.
  13. Remove the bracket from the washer solvent container
  14. Remove the washer solvent level sensor. Refer to Windshield Washer Solvent Level Switch Replacement .
  15. Remove the washer pump. Refer to Washer Pump Replacement .

Installation Procedure

    Object Number: 334222 Size: SH
  1. Install the washer pump. Refer to Washer Pump Replacement .
  2. Install the washer solvent level sensor. Refer to Windshield Washer Solvent Level Switch Replacement .
  3. Position the bracket to the washer solvent container.

    4. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  4. Install the washer solvent container bracket screws

    5. Tighten
    Tighten the washer solvent container bracket screws to 7 N·m (62 lb in).

  5. Connect the electrical connector to the washer solvent level sensor.
  6. Position the washer solvent container to the vehicle.
  7. Install the washer solvent container screws.

    8. Tighten
    Tighten the washer solvent container screws to 10 N·m (88 lb in).

  8. Connect the electrical connector and the hose to the washer pump.
  9. Install the front washer solvent container screw.

    10. Tighten
    Tighten the front washer solvent container screw to 5 N·m (44 lb in).

  10. Install the front fender liner. Refer to Front Fender Liner Replacement in Body Front End.
  11. Install the right headlamp assembly. Refer to Headlamp Assembly or Headlamp Bulb and/or Cornering, Sidemarker, Park, Turn Signal Bulb Replacement in Lighting Systems.

    12. Object Number: 334204 Size: SH
  12. Press the upper fill tube assembly and the seal onto the washer solvent container.
  13. Install the upper fill tube screw.

    14. Tighten
    Tighten the upper fill tube screw to 10 N·m (88 lb in).

  14. Fill the washer solvent container with washer solvent.