GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2001 🢒 Impala 🢒 Engine 🢒 Engine Controls - 3.8L 🢒 DTC P1133

Circuit Description

The powertrain control module (PCM) monitors the heated oxygen sensor (HO2S) activity for 100 seconds. During this test period, the PCM counts the number of times that the HO2S signal voltage crosses the rich-to-lean and the lean-to-rich thresholds. A lean-to-rich switch is determined when the HO2S voltage changes from less than 300 mV to more than 600 mV. A rich-to-lean switch is determined when the HO2S voltage changes from more than 600 mV to less than 300 mV. If the PCM determines that the HO2S did not switch enough times, DTC P1133 will set.

Conditions for Running the DTC
    • DTCs P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0117, P0118, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0300, P0410, P0440, P0442, P0443, P0446, P0449, and P1441 are not set.
    • The mass air flow (MAF) is between 10-30 g/s.
    • The ECT is more than 50°C (122°F).
    • The engine run time is more than 60 seconds.
    • The engine speed is between 1,000-3,000 RPM.
    • The engine is running in closed loop.

Conditions for Setting the DTC
    • The above conditions are present for a 100-second monitoring period.
    • The PCM monitors fewer than 40 rich-to-lean and 40 lean-to-rich switches for HO2S 1.

Action Taken When the DTC Sets
    • The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC
    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. When the system is operating correctly, the HO2S voltage should toggle above and below the specified values.

    2.

  2. If the HO2S low signal circuit is shorted to ground, the HO2S voltage will be less than 400 mV when the HO2S high signal circuit is jumped to ground.

    3.

  3. The specified value is what is measured on a correctly-operating system.

    4.

  4. The specified value is what is measured on a correctly-operating system.

P1133

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics

1

Did you perform the Diagnostic System Check-Engine Controls?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2

Important: If any other DTCs are set except the HO2S DTCs, refer to other DTCs first before proceeding with this table.

  1. Ensure that the engine is at the operating temperature.
  2. Operate engine above 1,200 RPM for 2 minutes.
  3. With a scan tool, observe the HO2S voltage parameter.

Does scan tool indicate that the HO2S voltage varies outside the specified values?

400-500 mV

Go to Step 3

Go to Step 4

3

Operate vehicle within the Failure Records conditions.

Does the scan tool indicate this DTC failed this ignition?

--

Go to Step 4

Go to Intermittent Conditions

4

Inspect and test for the following conditions:

    • An exhaust leak--Refer to Exhaust Leakage in Engine Exhaust.
    • Correct HO2S installation.
    • Damaged wiring--Refer to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 15

Go to Step 5

5

  1. Turn ON the ignition, with the engine OFF..
  2. Disconnect the HO2S.
  3. Jumper the high signal circuit on the PCM side to a good ground.
  4. With a scan tool, observe the HO2S voltage parameter.

Does the scan tool indicate that the HO2S voltage is more than the specified value?

400 mV

Go to Step 6

Go to Step 10

6

  1. Remove the jumper wire.
  2. Measure the voltage on the HO2S high signal circuit on the PCM side, using a DMM that is connected to a good ground.

Does the voltage measure near the specified value?

4.5 V

Go to Step 7

Go to Step 9

7

Measure the voltage on the HO2S low signal circuit on the PCM side, using a DMM that is connected to a good ground.

Does the voltage measure near the specified value?

5 V

Go to Step 11

Go to Step 8

8

Test the HO2S low signal circuit for an open or for high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 15

Go to Step 13

9

Test the HO2S high signal circuit for an open or for high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 15

Go to Step 13

10

Test the HO2S low signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 15

Go to Step 14

11

Test for poor connections at the HO2S. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 15

Go to Step 12

12

Important: Determine the cause of the contamination before replacing the sensor.

Inspect and test for the following conditions:

    • Fuel contamination--Refer to Alcohol/Contaminants-in-Fuel Diagnosis
        Engine oil or coolant consumption--Refer to Oil Consumption Diagnosis in Engine Mechanical.
    • Use of an improper RTV sealant. Refer to

Notice: Contamination of the oxygen sensor can result from the use of an inappropriate RTV sealant (not oxygen sensor safe) or excessive engine coolant or oil consumption. Remove the HO2S and visually inspect the portion of the sensor exposed to the exhaust stream in order to check for contamination. If contaminated, the portion of the sensor exposed to the exhaust stream will have a white powdery coating. Silicon contamination causes a high but false HO2S signal voltage (rich exhaust indication). The control module will then reduce the amount of fuel delivered to the engine, causing a severe driveability problem. Eliminate the source of contamination before replacing the oxygen sensor.

in Cautions and Notices.

Replace the affected HO2S sensor. Refer to Heated Oxygen Sensor 1 Replacement .

Did you complete the replacement?

--

Go to Step 15

--

13

Test for poor connections at the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 15

Go to Step 14

14

Replace the PCM. Refer to Powertrain Control Module Replacement

Did you complete the replacement?

--

Go to Step 15

--

15
  1. Use the scan tool in order to clear the DTCs.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC.

Does the DTC run and pass?

--

Go to Step 16

Go to Step 2

16

With a scan tool, observe the stored information in Capture Info.

Does the scan tool display any DTCs that have not been diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List

System OK