GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2001 🢒 Impala 🢒 Engine 🢒 Engine Electrical 🢒 Restricted Exhaust

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. The exhaust system has very low back pressure under normal conditions. If the exhaust system is restricted, a significant increase in the exhaust pressure is noticed on the J 35314-A .

    Removing the HO2S sensor may set a DTC. When finishing this diagnostic table, be sure to clear all codes.

  2. This step will isolate the catalytic converter from the remainder of the exhaust system.

    Perform operational check before returning vehicle to customer.

    3.

  3. Confirming that the condition has been fixed is essential. If the symptom still exists, proceed to Step 2 and repeat the diagnostic procedure.

    4.

  4. Confirming that the condition has been fixed is essential. If the symptom still exists, proceed to Step 2 and repeat the diagnostic procedure.

Restricted Exhaust

Step

Action

Value(s)

Yes

No

1

Did you verify the customers complaint?

--

Go to Step  2

--

2

Did you review the exhaust symptoms diagnostic information and perform the necessary inspections?

--

Go to Step  3

Go to Symptoms - Engine Exhaust

3

Caution: While engine is operating, the exhaust system will become extremely hot. To prevent burns avoid contacting a hot exhaust system.

  1. Remove the pre-catalyst HO2S sensor. Refer to Heated Oxygen Sensor 1 Replacement in Engine Controls-3.4L or Heated Oxygen Sensor 1 Replacement in Engine Controls-3.8L.
  2. Install the J 35314-A Exhaust Back Pressure Gage in place of the HO2S sensor.
  3. Start and run the engine.
  4. Increase and monitor the engine speed at 2500 RPM.
  5. Observe the exhaust system back pressure reading on the gage.

Does the reading exceed the specified value?

9 kPa (1.25 psi)

Go to Step  4

Go to Step  8

4

  1. Turn the engine off and place the ignition in the lock position.
  2. Remove the J 35314-A .
  3. Install the pre-catalyst HO2S sensor. Refer to Heated Oxygen Sensor 1 Replacement in Engine Controls-3.4L or Heated Oxygen Sensor 1 Replacement in Engine Controls-3.8L.
  4. Remove the post-catalyst HO2S sensor. Refer to Heated Oxygen Sensor 2 Replacement in Engine Controls-3.4L or Heated Oxygen Sensor 2 Replacement in Engine Controls-3.8L.
  5. Install the J 35314-A in place of the HO2S sensor.
  6. Start the and run the engine.
  7. Increase and monitor the engine speed at 2500 RPM.
  8. Observe the exhaust system back pressure reading on the gage.

Does the reading exceed the specified value?

9 kPa (1.25 psi)

Go to Step  5

Go to Step  6

5

Inspect the exhaust system for the following conditions:

    • Damage in the exhaust pipe.
    • Debris in the exhaust pipe
    • Muffler internal failure.
    • Two-layer exhaust pipe separation.

Did you find and correct the condition?

--

Go to Step  7

--

6

Replace the catalytic converter. Refer to Catalytic Converter Replacement .

Did you find and correct the condition?

--

Go to Step  7

--

7

  1. Remove the J 35314-A .
  2. Install the post-catalyst HO2S sensor. Refer to Heated Oxygen Sensor 2 Replacement in Engine Controls-3.4L or Heated Oxygen Sensor 2 Replacement in Engine Controls-3.8L.
  3. Clear any codes.
  4. Road test the vehicle in order to verify the repair.

Did you find and correct the condition?

--

System OK

Go to Step  2

8

  1. Remove the J 35314-A .
  2. Install the pre-catalyst HO2S sensor. Refer to Heated Oxygen Sensor 1 Replacement in Engine Controls-3.4L or Heated Oxygen Sensor 1 Replacement in Engine Controls-3.8L.
  3. Clear any codes.
  4. Road test the vehicle in order to verify the repair.

Did you find and correct the condition?

--

System OK

Go to Step  2