Emblem/Nameplate Replacement Monte Carlo Rear
Removal Procedure
Tools Required
J 25070 Heat Gun
- Apply tape to the area around the rear compartment lid applique emblem.
- Heat the emblem/name plate, using J 25070 152 mm (6 in) from the surface.
- Peel the emblem/name plate from the rear compartment lid surface using a small plastic flat-bladed tool. Do NOT damage the paint.
- Remove all adhesive from the rear compartment lid surface and the back of the emblem/name plate using 3M™ scotch brite molding adhesive remover disk, 3M™ P/N 07501 or equivalent.
- Clean the rear compartment lid surface using Varnish Makers and Painters (VM&P) naphtha.
Important: Use tape for protection and alignment marks for alignment of the new emblem.
Apply the heat using a circular motion for about 30 seconds.
Installation Procedure
- Mark the tape with the measurement for the proper location of the emblem.
- Warm the rear compartment lid surface with J 25070 152 mm (6 in) from the surface to a minimum of 21°C (70°F).
- Peel the backing from the front end of the emblem/name plate.
- Press the emblem/name plate to the rear compartment lid surface while continuing to remove the backing.
- Hand roll the emblem/name plate to the rear compartment lid in order to ensure proper adhesion.
- Inspect the emblem/name plate for bonding.
- Remove the tape from the area around the rear compartment lid emblem.
Do NOT touch the adhesive backing.
Hand roll the loose ends.
Emblem/Nameplate Replacement Monte CarloEmblem -Quarter Panel
Removal Procedure
Tools Required
J 25070 Heat Gun
- When replacing or repairing an emblem/nameplate do the following:
- To remove an emblem/nameplate, heat the emblem/nameplate using a J 25070
- Use a plastic, flat-bladed tool to lift or remove the emblem/nameplate from the panel surface.
- Apply the adhesive foam tape to the back of the emblem/nameplate and press the emblem/nameplate in place.
- When replacing, remove all adhesive as follows:
| 1.1. | Use tape to protect the mounting surface during removal. |
| 1.2. | Use tape for alignment marks for installation of the emblem/nameplate. |
Apply heat using a circular motion for about 30 seconds.
Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.
Important: If tape is still intact on the molding or panel, do not remove the tape. Clean the tape and the mating surface with adhesive cleaner. Wipe the tape and the mating surface with a clean, lint free cloth. If the tape is damaged, continue with the replacement procedure.
| • | For body panels use a 3M™ Scotch Brite molding adhesive remover disk 3M™ P/N 07501 or equivalent. |
| • | For plastic panels use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol and water in order to remove the adhesive. |
Installation Procedure
- Clean the area where the emblem/nameplate will be installed.
- Dry the area thoroughly.
- If the location of the emblem/nameplate has not been marked, apply tape and mark the location as shown.
- Heat the mounting surface to approximately 27-41°C (80-105°F).
- Ensure that the temperature of the emblem/name plate is approximately 29-32°C (85-90°F).
- Remove the protective liner from the back of the emblem/name plate.
- Position the emblem/name plate to the location marks and press the emblem/name plate to the mounting surface.
- Apply equal pressure along the emblem/name plate in order to uniformly bond the item to the mounting surface.
- Remove the protective tape from the mounting surface.
Important: Apply the emblem/nameplate in an environment that is free from dust or other dirt that could come into contact with the sticky backing. Foreign material may cause improper adhesion.
Use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol and water in order to clean the area.
Emblem/Nameplate Replacement Impala Quarter Panel
Removal Procedure
Tools Required
J 25070 Heat Gun
- When replacing or repairing an emblem/nameplate do the following:
- To remove an emblem/nameplate, heat the emblem/nameplate using a J 25070
- Use a plastic, flat-bladed tool to lift or remove the emblem/nameplate from the panel surface.
- Apply the adhesive foam tape to the back of the emblem/nameplate and press the emblem/nameplate in place.
- When replacing, remove all adhesive as follows:
| 1.1. | Use tape to protect the mounting surface during removal. |
| 1.2. | Use tape for alignment marks for installation of the emblem/nameplate. |
Apply heat using a circular motion for about 30 seconds.
Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.
Important: If tape is still intact on the molding or panel, do not remove the tape. Clean the tape and the mating surface with adhesive cleaner. Wipe the tape and the mating surface with a clean, lint free cloth. If the tape is damaged, continue with the replacement procedure.
| • | For body panels use a 3M™ Scotch Brite molding adhesive remover disk 3M™ P/N 07501 or equivalent. |
| • | For plastic panels use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol and water in order to remove the adhesive. |
Installation Procedure
- Clean the area where the emblem/nameplate will be installed.
- Dry the area thoroughly.
- If the location of the emblem/nameplate has not been marked, apply tape and mark the location as shown.
- Heat the mounting surface to approximately 27-41°C (80-105°F).
- Ensure that the temperature of the emblem/name plate is approximately 29-32°C (85-90°F).
- Remove the protective liner from the back of the emblem/name plate.
- Position the emblem/name plate to the location marks and press the emblem/name plate to the mounting surface.
- Apply equal pressure along the emblem/name plate in order to uniformly bond the item to the mounting surface.
- Remove the protective tape from the mounting surface.
Important: Apply the emblem/nameplate in an environment that is free from dust or other dirt that could come into contact with the sticky backing. Foreign material may cause improper adhesion.
Use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol and water in order to clean the area.
Emblem/Nameplate Replacement Impala Rear
Removal Procedure
Tools Required
J 25070 Heat Gun
- When replacing or repairing an emblem/nameplate do the following:
- To remove an emblem/nameplate, heat the emblem/nameplate using a J 25070
- Use a plastic, flat-bladed tool to lift or remove the emblem/nameplate from the panel surface.
- Apply the adhesive foam tape to the back of the emblem/nameplate and press the emblem/nameplate in place.
- When replacing, remove all adhesive as follows:
| 1.1. | Use tape to protect the mounting surface during removal. |
| 1.2. | Use tape for alignment marks for installation of the emblem/nameplate. |
Apply heat using a circular motion for about 30 seconds.
Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.
Important: If tape is still intact on the molding or panel, do not remove the tape. Clean the tape and the mating surface with adhesive cleaner. Wipe the tape and the mating surface with a clean, lint free cloth. If the tape is damaged, continue with the replacement procedure.
| • | For body panels use a 3M™ Scotch Brite molding adhesive remover disk 3M™ P/N 07501 or equivalent. |
| • | For plastic panels use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol and water in order to remove the adhesive. |
Installation Procedure
- Clean the area where the emblem/nameplate will be installed.
- Dry the area thoroughly.
- If the location of the emblem/nameplate has not been marked, apply tape and mark the location as shown.
- Heat the mounting surface to approximately 27-41°C (80-105°F).
- Ensure that the temperature of the emblem/name plate is approximately 29-32°C (85-90°F).
- Remove the protective liner from the back of the emblem/name plate.
- Position the emblem/name plate to the location marks and press the emblem/name plate to the mounting surface.
- Apply equal pressure along the emblem/name plate in order to uniformly bond the item to the mounting surface.
- Remove the protective tape from the mounting surface.
Important: Apply the emblem/nameplate in an environment that is free from dust or other dirt that could come into contact with the sticky backing. Foreign material may cause improper adhesion.
Use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol and water in order to clean the area.
Emblem/Nameplate Replacement Impala Door
Removal Procedure
Tools Required
J 25070 Heat Gun
- When replacing or repairing an emblem/nameplate do the following:
- To remove an emblem/nameplate, heat the emblem/nameplate using a J 25070
- Use a plastic, flat-bladed tool to lift or remove the emblem/nameplate from the panel surface.
- Apply the adhesive foam tape to the back of the emblem/nameplate and press the emblem/nameplate in place.
- When replacing, remove all adhesive as follows:
| 1.1. | Use tape to protect the mounting surface during removal. |
| 1.2. | Use tape for alignment marks for installation of the emblem/nameplate. |
Apply heat using a circular motion for about 30 seconds.
Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.
Important: If tape is still intact on the molding or panel, do not remove the tape. Clean the tape and the mating surface with adhesive cleaner. Wipe the tape and the mating surface with a clean, lint free cloth. If the tape is damaged, continue with the replacement procedure.
| • | For body panels use a 3M™ Scotch Brite molding adhesive remover disk 3M™ P/N 07501 or equivalent. |
| • | For plastic panels use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol and water in order to remove the adhesive. |
Installation Procedure
- Clean the area where the emblem/nameplate will be installed.
- Dry the area thoroughly.
- If the location of the emblem/nameplate has not been marked, apply tape and mark the location as shown.
- Heat the mounting surface to approximately 27-41°C (80-105°F).
- Ensure that the temperature of the emblem/name plate is approximately 29-32°C (85-90°F).
- Remove the protective liner from the back of the emblem/name plate.
- Position the emblem/name plate to the location marks and press the emblem/name plate to the mounting surface.
- Apply equal pressure along the emblem/name plate in order to uniformly bond the item to the mounting surface.
- Remove the protective tape from the mounting surface.
Important: Apply the emblem/nameplate in an environment that is free from dust or other dirt that could come into contact with the sticky backing. Foreign material may cause improper adhesion.
Use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol and water in order to clean the area.
Emblem/Nameplate Replacement Impala Rear Applique
Removal Procedure
Tools Required
J 25070 Heat Gun
- When replacing or repairing an emblem/nameplate do the following:
- To remove an emblem/nameplate, heat the emblem/nameplate using a J 25070
- Use a plastic, flat-bladed tool to lift or remove the emblem/nameplate from the panel surface.
- Apply the adhesive foam tape to the back of the emblem/nameplate and press the emblem/nameplate in place.
- When replacing, remove all adhesive as follows:
| 1.1. | Use tape to protect the mounting surface during removal. |
| 1.2. | Use tape for alignment marks for installation of the emblem/nameplate. |
Apply heat using a circular motion for about 30 seconds.
Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.
Important: If tape is still intact on the molding or panel, do not remove the tape. Clean the tape and the mating surface with adhesive cleaner. Wipe the tape and the mating surface with a clean, lint free cloth. If the tape is damaged, continue with the replacement procedure.
| • | For body panels use a 3M™ Scotch Brite molding adhesive remover disk 3M™ P/N 07501 or equivalent. |
| • | For plastic panels use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol and water in order to remove the adhesive. |
Installation Procedure
- Clean the area where the emblem/nameplate will be installed.
- Dry the area thoroughly.
- If the location of the emblem/nameplate has not been marked, apply tape and mark the location as shown.
- Heat the mounting surface to approximately 27-41°C (80-105°F).
- Ensure that the temperature of the emblem/name plate is approximately 29-32°C (85-90°F).
- Remove the protective liner from the back of the emblem/name plate.
- Position the emblem/name plate to the location marks and press the emblem/name plate to the mounting surface.
- Apply equal pressure along the emblem/name plate in order to uniformly bond the item to the mounting surface.
- Remove the protective tape from the mounting surface.
Important: Apply the emblem/nameplate in an environment that is free from dust or other dirt that could come into contact with the sticky backing. Foreign material may cause improper adhesion.
Use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol and water in order to clean the area.
Emblem/Nameplate Replacement Monte Carlo Nameplate - Quarter Panel
Removal Procedure
Tools Required
J 25070 Heat Gun
- When replacing or repairing an emblem/nameplate do the following:
- To remove an emblem/nameplate, heat the emblem/nameplate using a J 25070
- Use a plastic, flat-bladed tool to lift or remove the emblem/nameplate from the panel surface.
- Apply the adhesive foam tape to the back of the emblem/nameplate and press the emblem/nameplate in place.
- When replacing, remove all adhesive as follows:
| 1.1. | Use tape to protect the mounting surface during removal. |
| 1.2. | Use tape for alignment marks for installation of the emblem/nameplate. |
Apply heat using a circular motion for about 30 seconds.
Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.
Important: If tape is still intact on the molding or panel, do not remove the tape. Clean the tape and the mating surface with adhesive cleaner. Wipe the tape and the mating surface with a clean, lint free cloth. If the tape is damaged, continue with the replacement procedure.
| • | For body panels use a 3M™ Scotch Brite molding adhesive remover disk 3M™ P/N 07501 or equivalent. |
| • | For plastic panels use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol and water in order to remove the adhesive. |
Installation Procedure
- Clean the area where the emblem/nameplate will be installed.
- Dry the area thoroughly.
- If the location of the emblem/nameplate has not been marked, apply tape and mark the location as shown.
- Heat the mounting surface to approximately 27-41°C (80-105°F).
- Ensure that the temperature of the emblem/name plate is approximately 29-32°C (85-90°F).
- Remove the protective liner from the back of the emblem/name plate.
- Position the emblem/name plate to the location marks and press the emblem/name plate to the mounting surface.
- Apply equal pressure along the emblem/name plate in order to uniformly bond the item to the mounting surface.
- Remove the protective tape from the mounting surface.
Important: Apply the emblem/nameplate in an environment that is free from dust or other dirt that could come into contact with the sticky backing. Foreign material may cause improper adhesion.
Use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a (50/50 mixture) by volume of isopropyl alcohol and water in order to clean the area.
