Trunk Ajar Indicator Always On Convertible
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Instrument Cluster Schematics Connector End View Reference: Displays and Gages Connector End Views | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | |
2 | Close the rear compartment. Is the TRUNK AJAR message displayed on the driver information center (DIC)? | Go to Step 3 | Go to Testing for Intermittent Conditions and Poor Connections |
3 |
Does the scan tool display TRUNK AJAR? | Go to Step 4 | Go to Step 6 |
4 | Disconnect the trunk release actuator. Is the trunk ajar message displayed? | Go to Step 5 | Go to Step 7 |
5 | Inspect for a short to ground in the trunk ajar switch signal circuit. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 8 |
6 | Inspect for poor connections at the harness connector of the instrument panel cluster (IPC). Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 9 |
7 | Inspect for poor connections at the harness connector of the trunk release actuator. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 10 |
8 | Inspect for poor connections at the harness connector of the BCM. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 11 |
9 | Replace the IPC. Refer to Control Module References for replacement, setup, and programming. Did you complete the repair? | Go to Step 12 | -- |
10 | Replace the trunk release actuator. Refer to Rear Compartment Lid and Fuel Filler Door Release Switch Replacement . Did you complete the repair? | Go to Step 12 | -- |
11 | Replace the BCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | Go to Step 12 | -- |
12 | Operate the system in order to verify the repair. Did you correct the condition? | System OK | Go to Step 3 |
Trunk Ajar Indicator Always On Coupe
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Instrument Cluster Schematics Connector End View Reference: Displays and Gages Connector End Views | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | |
2 | Close the rear compartment. Is the HATCH AJAR message displayed on the driver information center (DIC)? | Go to Step 3 | Go to Testing for Intermittent Conditions and Poor Connections |
3 |
Does the scan tool display TRUNK AJAR? | Go to Step 4 | Go to Step 6 |
4 | Disconnect the rear compartment lid pull down actuator. Is the trunk ajar message displayed? | Go to Step 5 | Go to Step 7 |
5 | Inspect for a short to ground in the trunk ajar switch signal circuit. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 8 |
6 | Inspect for poor connections at the harness connector of the instrument panel cluster (IPC). Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 9 |
7 | Inspect for poor connections at the harness connector of the rear compartment lid pull down actuator. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 10 |
8 | Inspect for poor connections at the harness connector of the BCM. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 11 |
9 | Replace the IPC. Refer to Control Module References for replacement, setup, and programming. Did you complete the repair? | Go to Step 12 | -- |
10 | Replace the rear compartment lid pull down actuator. Refer to Rear Compartment Lid and Fuel Filler Door Release Switch Replacement . Did you complete the repair? | Go to Step 12 | -- |
11 | Replace the BCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | Go to Step 12 | -- |
12 | Operate the system in order to verify the repair. Did you correct the condition? | System OK | Go to Step 3 |
