Turn Signal Cancel Cam and Steering Shaft Upper Bearing Spring Replacement Telescoping

Caution: Refer to SIR Caution in the Preface section.




1. Disable the SIR system. Refer to SIR Disabling and Enabling in SIR.

Important: Let the SIR coil hang freely after removal.

2. Remove the SIR coil from the steering column. Refer to Inflatable Restraint Steering Wheel Module Coil Replacement in SIR.
3. Remove the wave washer (1) from the steering shaft assembly (2).



4. Compress the cam orientation plate using J 23653-SIR and J 42137 .
5. Remove the bearing retainer from the steering shaft assembly.
6. Remove J 23653-SIR and J 42137 .
7. Dispose of the bearing retainer.



8. Remove the following from the steering shaft:

8.1.	Shaft lock shield (5)

8.2.	Turn signal cancel cam assembly (4)

8.3.	Upper bearing spring (3)

8.4.	Upper bearing inner race seat (2)

8.5.	Inner race (1)

1. Install the following to the steering shaft:

1.1.	Inner race (1)

1.2.	Upper bearing inner race seat (2)

1.3.	Upper bearing spring (3)

1.4.	Turn signal cancel cam assembly (4)

1.5.	Shaft lock shield (5)





Important: The bearing retainer must be properly seated into the groove on the steering shaft.

2. Install a new bearing retainer onto the steering shaft assembly.
3. Compress the cam orientation plate using J 23653-SIR and J 42137 to install the bearing retainer.
4. Remove J 23653-SIR and J 42137 from the steering shaft assembly.



5. Install the wave washer (1) onto the steering shaft assembly (2).
6. Install the SIR coil. Refer to Inflatable Restraint Steering Wheel Module Coil Replacement in SIR.
7. Enable the SIR system. Refer to SIR Disabling and Enabling in SIR.

Turn Signal Cancel Cam and Steering Shaft Upper Bearing Spring Replacement Manual

Caution: Refer to SIR Caution in the Preface section.




1. Disable the SIR system. Refer to SIR Disabling and Enabling in SIR.

Important: Let the SIR coil hang freely after removal.

2. Remove the SIR coil from the steering column. Refer to Inflatable Restraint Steering Wheel Module Coil Replacement in SIR.
3. Remove the wave washer (1) from the steering shaft assembly (2).



4. Compress the cam orientation plate using J 23653-SIR and J 42137 .
5. Remove the bearing retainer from the steering shaft assembly.
6. Remove J 23653-SIR and J 42137 .
7. Dispose of the bearing retainer.



8. Remove the following from the steering shaft:

8.1.	Shaft lock shield (5)

8.2.	Turn signal cancel cam assembly (4)

8.3.	Upper bearing spring (3)

8.4.	Upper bearing inner race seat (2)

8.5.	Inner race (1)

1. Install the following to the steering shaft:

1.1.	Inner race (1)

1.2.	Upper bearing inner race seat (2)

1.3.	Upper bearing spring (3)

1.4.	Turn signal cancel cam assembly (4)

1.5.	Shaft lock shield (5)





Important: The bearing retainer must be properly seated into the groove on the steering shaft.

2. Install a new bearing retainer onto the steering shaft assembly.
3. Compress the cam orientation plate using J 23653-SIR and J 42137 to install the bearing retainer.
4. Remove J 23653-SIR and J 42137 from the steering shaft assembly.



5. Install the wave washer (1) onto the steering shaft assembly (2).
6. Install the SIR coil. Refer to Inflatable Restraint Steering Wheel Module Coil Replacement in SIR.
7. Enable the SIR system. Refer to SIR Disabling and Enabling in SIR.