The following information covers the tests, inspections, and services required to maintain the safety, dependability, and emission control performance of the vehicle.

Ensure that any necessary repairs are completed on time. Whenever any fluids and/or lubricants are added to the vehicle, ensure to use the proper fluids and/or lubricants. Refer to Fluid and Lubricant Recommendations .

Perform the following underhood inspections at each fuel fill.

Inspect the engine oil level and add the proper oil when necessary. Refer to Fluid and Lubricant Recommendations .

Inspect the engine coolant level and add the proper coolant mixture when necessary. Refer to Fluid and Lubricant Recommendations .

Inspect the windshield washer fluid level in the windshield washer reservoir and add the proper fluid when necessary. Refer to Fluid and Lubricant Recommendations .

Tire Inflation Check

Inspect the tire inflation. ensure that the tires are inflated to the pressures specified on the Certification/Tire label located on the driver's door lock pillar.

Cassette Deck Service

Clean the playback heads and the capstan of the cassette deck. Cleaning should be done after every 50 hours of tape playing time.

Power Antenna Service

Clean the power antenna mast.

Restraint System Check

Ensure the safety belt reminder light and all of your belts, buckles, latch plates, retractors, and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep am safety belt system from doing its job, have it repaired. Have any torn or frayed safety belts replaced.

Also look for any opened or broken air bag coverings, and have them repaired or replaced. The SIR system does not need regular maintenance.

Wiper Blade Check

Inspect wiper blades for wear or cracking. Replace the blade inserts that appear worn or damaged or that streak or miss areas of the windshield.

Weatherstrip Lubrication

Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather more frequent application may be required.

Manual Transmission Check

Inspect the automatic transmission fluid level; add if needed. A fluid loss may indicate a problem. Check for leaks. A fluid leak is the only reason for fluid loss. Inspect the system and repair as needed.

Automatic Transmission Inspection

It is not necessary to check the transmission fluid level. A transmission fluid leak is the only reason for fluid loss. Check for leaks. Inspect the system and repair as needed.

Key Lock Cylinders

Lubricate the lock cylinders with the recommended lubricant. Refer to Fluid and Lubricant Recommendations .

Important: More frequent lubrication may be required when any of the listed parts are exposed to a corrosive environment. In order to locate the proper lubricant, refer to Fluid and Lubricant Recommendations .

Body Lubrications

Lubricate all of the following areas:

Starter Switch

Test the starter switch:

For vehicles equipped with the manual transmission, place the shift lever in the NEUTRAL (N) position, push the clutch pedal in halfway, and try to start the engine. The starter should work only when the clutch pedal is pushed all the way to the floor. If the starter works when the clutch pedal is not pushed all the way in, the vehicle requires immediate service.

Automatic Transmission Shift Lock Control System Check

Ignition Transmission Lock Check

1. Ensure that the vehicle is parked.
2. Ensure that the vehicle park brake is set.
3. Try to turn the ignition key in each shift lever position.
4. Attempt to turn the ignition key to the LOCK position.
5. The key should turn to LOCK only when the shift lever is in PARK (P).
6. The key should come out only in LOCK.

Parking Brake and Automatic Transmission PARK (P) Mechanism Check

Caution: When performing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case the vehicle begins to roll. Be ready to apply the regular brake at once, should the vehicle begin to move.

Test the parking brake and automatic transmission PARK (P) mechanism.

Follow this procedure to test the parking brake and automatic transmission PARK mechanism:

1. Park on a fairly steep hill, with the vehicle facing downhill.
2. Keep your foot on the brake pedal.
3. Set the parking brake.
4. In order to test the parking brake:

4.1.	Start the engine.

4.2.	Place the shift lever in the NEUTRAL (N) position.

4.3.	Slowly remove foot pressure from the brake pedal.

5. In order to test the PARK (P) mechanism, follow steps 1-3 above and then do the following:

5.1.	Place the shift lever in the PARK (P) position.

5.2.	Release all of the brakes.

Underbody Flushing Service

Once every spring, use plain water to flush any corrosive materials from the underbody. Clean thoroughly any areas where mud and other debris can collect.