Rear Compartment Side Trim Panel Replacement Coupe

1. Open and support the rear lift window.



2. Remove the strut. Refer to Rear Compartment Lift Window Strut Replacement in Body Rear End.



3. Uncover the upper seat belt guide bolt by pushing up at the belt edge of the bolt cover.
4. Remove the seat belt guide bolt.



5. Remove the roof lift off panel.
6. Remove the rear roof bow interior trim panel. Refer to Rear Roof Bow Trim Panel Replacement .



7. Remove the fasteners securing the rear roof bow weatherstrip to the lock pillar.



8. Remove the push-in fastener securing the top of the side trim panel.
9. Remove the speaker grille from the side trim panel.

9.1.	Pry out the middle of the forward edge first.

9.2.	Pry out the top or the middle of the rear edge.

9.3.	Lift the grille up out of the panel.

10. Remove the fir tree push-in retainer from the rear of the grille opening.
11. Remove the side trim panel.

1. Position the side trim panel to the lock pillar.
2. Secure the panel with the push-in fastener and hook and loop fasteners.
3. Install the fir tree push-in retainer to the rear of the speaker grill opening.
4. Insert the lower tab of the grille into the opening and snap the grille in place.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

5. Install the seat belt guide bolt and cover.

Tighten
Tighten the seat belt guide bolt to 46 N·m (34 lb ft).




6. Install the strut. Refer to Rear Compartment Lift Window Strut Replacement in Body Rear End.



7. Install the push-in fasteners attaching the weatherstrip to the lock pillar.



8. Install the rear roof bow interior trim panel and the roof lift off panel. Refer to Rear Roof Bow Trim Panel Replacement .
9. Remove the support and close the lift window.

Rear Compartment Side Trim Panel Replacement Convertible

1. Open the folding top stowage lid.
2. Remove the push pin from the front of the side trim panel.
3. Pull the panel from the housing.

1. Position the side trim panel with the front edge of the panel under the lock pillar flange.
2. Install the push pin attaching the panel to the lock pillar.
3. Align the panel clips to the holes in the housing.
4. Press the panel at the clip locations to secure the clips.

Rear Compartment Side Trim Panel Replacement Hardtop

1. Remove the push pins from the ends of the lower garnish molding.
2. Pull the molding with the molding retainers from the body panel.
3. Remove the rear window lower garnish molding.



4. Remove the support trim panel from rear compartment front support.



5. Uncover the seat belt upper guide bolt by pushing up at the belt edge of the cover and flipping up the cover.
6. Remove the seat belt upper guide bolt.



7. Remove the push-in retainer attaching the side trim panel to the rear compartment front support.
8. Pull the side trim panel from the rear side of the roof.
9. Pull the side trim panel from the roof bow.
10. Pull the side trim panel from the lock pillar.

1. Position the side trim panel to the vehicle.
2. Secure the panel to the roof bow.
3. Secure the side trim panel to the lock pillar.
4. Secure the side trim panel to the rear compartment support with a push in retainer.
5. Secure the side trim panel to the side of the roof.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

6. Install the seat belt upper guide bolt and cover.

Tighten
Tighten the seat belt guide bolt to 41 N·m (31 lb ft).

7. Snap the cover closed.



8. Install the rear compartment support trim panel.



9. Align the rear window lower garnish molding retainers to the holes in the roof panel.
10. Push firmly on the garnish molding seating the retainers.
11. Install the push pins securing the ends of the garnish molding.