GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2001 🢒 Corvette 🢒 Body and Accessories 🢒 Roof 🢒 Folding Top Headlining Trim Panel Replacement

Removal Procedure

    Object Number: 289910 Size: SH
  1. Position the folding top with the #1 and #5 bow up.
  2. Remove the seal compression panel. Refer To Folding Top Seal Compression Panel Replacement .

    3. Object Number: 784488 Size: SH
  3. Using a pair of needle nose pliers remove the top cover staples from the #1 bow.

    4. Object Number: 784495 Size: SH
  4. Using a pair of needle nose pliers remove the headliner staples from the #1 bow.
  5. Pull the top cover back over the #3 bow.

    6. Object Number: 784498 Size: SH
  6. Remove the headliner side screws from the #1 bow.

    7. Object Number: 784499 Size: SH
  7. Using a pair of needle nose pliers remove the headliner extension push on retainers from the studs on the #1 bow.

    8. Object Number: 784505 Size: SH
  8. Remove the headliner retainer screws from the #2 bow.

    9. Object Number: 214136 Size: SH
  9. Position the top in a closed position with the folding top stowage lid open to gain access to the headliner attachments.
  10. Remove the headliner elastic strap retainer screws from the #5 bow.
  11. Remove the headliner elastic strap retainer screws from the rear side rail.
  12. Remove the headliner screws from the rear side rail.

    13. Object Number: 289910 Size: SH
  13. Position the #1 and #5 bow up to gain access to the #4 bow screws.

    14. Object Number: 784512 Size: SH
  14. Remove the rear window support strap screws from the number four bow.
  15. Remove the headliner retainer screws from the #4 bow.

    16. Object Number: 784514 Size: SH
  16. Remove the headliner retainer screws from the #3 bow.
  17. Remove the headliner.

Installation Procedure
  1. Install the headliner retainer to the #3 bow.

    2. Object Number: 784514 Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  2. Install the headliner retainer screws to the #3 bow.

    3. Tighten
    Tighten the screws to 2 N·m (18 lb in).

  3. Install the headliner retainer screws to the #4 bow.

    4. Tighten
    Tighten the screws to 2 N·m (18 lb in).


    Object Number: 784512 Size: SH
  4. Install the rear window support strap screws to the #4 bow.

    5. Tighten
    Tighten the screws to 2 N·m (18 lb in).

  5. Install the headliner elastic strap retainer screws to the rear side rails.

    6. Tighten
    Tighten the screws to 2 N·m (18 lb in).

  6. Install the headliner screws to the rear side rails.

    7. Tighten
    Tighten the screws to 2 N·m (18 lb in).

  7. Install the headliner elastic strap retainers screws to the #5 bow.

    8. Tighten
    Tighten the screws to 2 N·m (18 lb in).


    Object Number: 289910 Size: SH
  8. Position the #1 and #5 bow up.

    9. Object Number: 784505 Size: SH
  9. Install the headliner retainer screws to the #2 bow.

    10. Tighten
    Tighten the to 2 N·m (18 lb in).


    Object Number: 784499 Size: SH
  10. Install the headliner extension push on retainers to the #1 bow stud.

    11. Object Number: 784498 Size: SH
  11. Install the right and left side headliner screws to the #1 bow.

    12. Tighten
    Tighten the screws to 2 N·m (18 lb in).


    Object Number: 790096 Size: SH
  12. Staple the headliner to the #1 bow.
  13. Before stapling the top cover to the #1 bow, refer To Folding Top Cover Tension Adjustment - Front .
  14. Reposition the folding top to the original position.